User Manual
Table Of Contents
- Uso del presente Manuale di riferimento
- Sommario
- Schema delle funzioni
- Sezione SELECTED CHANNEL (CANALE SELEZIONATO)
- Sezione Channel Strip
- Assegnazione ingressi e uscite
- Canali di ingresso
- Flusso del segnale dei canali di ingresso
- Indicazione del nome, dell'icona e del colore del canale
- Impostazione HA (Preamplificatore)
- Invio di un segnale dal canale di ingresso al bus STEREO/MONO
- Funzione pan aggiunta (solo canali di ingresso mono)
- Invio di un segnale da un canale di ingresso a un bus MIX/MATRIX
- Indicazione del display dei nomi dei canali
- Correzione del delay tra i canali (Input Delay) (Delay di ingresso)
- Uscita surround per i canali di ingresso
- Funzionamento della libreria canali
- Canali OUTPUT
- Flusso del segnale dei canali di uscita
- Indicazione del nome, dell'icona e del colore del canale
- Invio dei segnali dai canali MIX al bus STEREO/MONO
- Invio dei segnali dai canali MIX e STEREO/MONO ai bus MATRIX
- Correzione del delay tra i canali (Output Delay)
- Utilizzo della funzione PORT TO PORT (PORTA A PORTA)
- Funzionamento della libreria canali
- EQ e dinamiche
- Channel Job (Operazione canale)
- Memoria scena
- Memorizzazione e richiamo di scene
- Modifica delle memorie scene
- Uso della funzione Global Paste (Incolla impostazioni globali)
- Utilizzo della funzione Focus Recall
- Utilizzo della funzione Fade
- Uscita di un segnale di controllo a un dispositivo esterno collegato con richiamo della scena (GPI OUT)
- Riproduzione di un file audio collegato al richiamo di una scena
- Uso della modalità Preview
- Funzioni Monitor (Monitoraggio) e Cue (Segnale di attivazione)
- Talkback e oscillatore
- Indicatori
- EQ grafico, Equalizzatore parametrico, effetti e Premium Rack
- Dispositivi I/O e preamplificatori esterni
- Uso di un dispositivo I/O
- Controllo remoto di un'unità della serie R
- Funzione di controllo dei preamplificatori dei dispositivi di terze parti aggiunta
- Controllo remoto di un amplificatore
- Controllo remoto di un'unità WIRELESS
- Uso di un preamplificatore esterno
- Controllo remoto di un preamplificatore esterno
- Controllo di un preamplificatore interno
- MIDI
- Registratore
- Informazioni sul registratore di memoria USB
- Assegnazione dei canali all'ingresso/uscita del registratore
- Registrazione dell'audio mediante un'unità flash USB
- Riproduzione di file audio da un'unità flash USB
- Modifica dell'elenco dei titoli
- Registrazione o riproduzione su un computer mediante DAW
- Utilizzo della console QL con Nuendo Live
- Control AFC IMAGE
- Configurazione
- Informazioni sulla schermata SETUP (CONFIGURAZIONE)
- Impostazioni utente
- Preferenze
- Tasti USER DEFINED
- Funzioni che possono essere assegnate a tasti USER DEFINED
- Manopole USER DEFINED
- Funzioni che è possibile assegnare alle manopole USER DEFINED
- Banco di fader personalizzato
- Console Lock
- Salvataggio e caricamento di dati di configurazione in e da un'unità flash USB
- Funzione per rimontare le unità flash USB aggiunta
- Impostazioni di wordclock e slot
- Utilizzo dei collegamenti in cascata
- Impostazioni di base per i bus MIX e MATRIX
- Attivazione o disattivazione dell'intera alimentazione phantom
- Regolazione della luminosità dello schermo sensibile al tocco, dei LED, della visualizzazione dei nomi dei canali e delle spie
- Impostazione di data/ora del clock interno
- Impostazione dell'indirizzo di rete
- Configurazione della rete audio Dante
- Dante Device Lock
- Supporto per Dante Domain Manager
- Utilizzo di GPI (General Purpose Interface)
- Funzione Help (Guida)
- Altre funzioni
- Inizializzazione dell'unità alle impostazioni di fabbrica predefinite
- Regolazione del punto di rilevamento dello schermo sensibile al tocco (funzione Calibration, Calibratura)
- Regolazione dei fader (funzione Calibration)
- Regolazione fine del guadagno di input e uscita (funzione Calibration)
- Regolazione del colore dei LED (funzione Calibration)
- Regolazione della luminosità del display dei nomi dei canali
- Regolazione del contrasto dei display dei nomi dei canali
- Inizializzazione delle impostazioni della rete audio Dante
- Procedura di aggiornamento modificata per il firmware NAME SUB CPU
- Funzione di aggiornamento del firmware Dante aggiunta
- Messaggi di avviso/errore
- Indice
- Data List
Data List
19
EQUALIZER601
This effect emulates the characteristics of 70’s analog equalizers. Re-creating the distortion
of typical analog circuits will add drive to the sound.
OPENDECK
It emulates the tape compression created by two open reel tape recorders (a recording deck
and a playback deck). You can change the sound quality by adjusting various elements, such
as the deck type, tape quality, playback speed, etc.
M.BAND DYNA.
Two input, two output 3-band dynamics processor, with individual solo and gain reduction
metering for each band.
Parameter Range Description
LO TYPE HPF-2/1, LSH-1/2 Type of EQ1
LO F 16.0 Hz to 20.0 kHz Cut-off frequency of EQ1
LO G –18.0 to +18.0 dB Gain of EQ1
MID1 Q 0.50–16.0 Q of EQ2
MID1 F 16.0 Hz to 20.0 kHz Center frequency of EQ2
MID1 G –18.0 to +18.0 dB Gain of EQ2
MID2 Q 0.50–16.0 Q of EQ3
MID2 F 16.0 Hz to 20.0 kHz Center frequency of EQ3
MID2 G –18.0 to +18.0 dB Gain of EQ3
INPUT –18.0 to +18.0 dB Input gain
OUTPUT –18.0 to +18.0 dB Output gain
MID3 Q 0.50–16.0 Q of EQ4
MID3 F 16.0 Hz to 20.0 kHz Center frequency of EQ4
MID3 G –18.0 to +18.0 dB Gain of EQ4
MID4 Q 0.50–16.0 Q of EQ5
MID4 F 16.0 Hz to 20.0 kHz Center frequency of EQ5
MID4 G –18.0 to +18.0 dB Gain of EQ5
HI TYPE LPF-2/1, HSH-1/2 Type of EQ6
HI F
16.0 Hz to 20.0 kHz
*1
*1. 16.0 Hz to 20.0 kHz (LPF-1, LPF-2), 1.0 kHz to 20.0 kHz (HSH-1, HSH-2)
Cut-off frequency of EQ6
HI G –18.0 to +18.0 dB Gain of EQ6
LO SW OFF, ON Switches EQ1 on/off
MID1 SW OFF, ON Switches EQ2 on/off
MID2 SW OFF, ON Switches EQ3 on/off
MID3 SW OFF, ON Switches EQ4 on/off
MID4 SW OFF, ON Switches EQ5 on/off
HI SW OFF, ON Switches EQ6 on/off
TYPE CLEAN, DRIVE
Selects the equalizer type.
The CLEAN equalizer provides non-distorted, clear, typical digital sound,
emulating variations in frequency response in the analog circuits. The
DRIVE equalizer provides distorted, driven sound that enhances analog
flavor, emulating changes in frequency response in the analog circuits.
Parameter Range Description
REC DEC
Swss70, Swss78, Swss85,
Amer70
Selects the recording deck type
REC LVL –96.0 to +18.0 dB
Adjusts the input level of the recording deck. As you raise the level, tape
compression is generated, which narrows the dynamic range and distorts
the sound.
REC HI –6.0 to +6.0 dB Adjusts the high range gain of the recording deck
REC BIAS –1.00 to +1.00 Adjusts the bias of the recording deck
REPR DEC
Swss70, Swss78, Swss85,
Amer70
Selects the playback deck type
REPR LVL –96.0 to +18.0 dB Adjusts the output level of the playback deck
REPR HI –6.0 to +6.0 dB Adjusts the high range gain of the playback deck
REPR LO –6.0 to +6.0 dB Adjusts the low range gain of the playback deck
MAKE UP Off, On
When you adjust the REC LVL, the REPR LVL reflects the change,
maintaining the relative output level. You can change the amount of
distortion without changing the output level.
TP SPEED 15ips, 30ips Selects the tape speed
TP KIND Old, New Selects the tape type
Parameter Range Description
L-M XOVER 21.2 Hz–8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz–8.00 kHz Crossover frequency between the mid and high bands
SLOPE –6 dB, –12 dB Filter slope
LOW GAIN –12.0 dB to +12.0 dB Low band gain
MID GAIN –12.0 dB to +12.0 dB Mid band gain
HI. GAIN –12.0 dB to +12.0 dB High band gain
TOTAL –72.0 dB to +12.0 dB Overall gain
CEILING –6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
CMP.THRE –24.0 dB to 0.0 dB Threshold of the compressor
CMP.RAT 1:1 to 20:1 Ratio of the compressor
CMP.ATK 0–120 ms Attack time of the compressor
CMP.REL
*1
Release time of the compressor
CMP.KNEE 0–5 Knee of the compressor
CMP.BYP OFF/ON Bypasses the compressor
EXP.THRE –54.0 dB to –24.0 dB Threshold of the expander
EXP.RAT 1:1 to 5:1 Ratio of the expander
EXP.REL
*1
Release time of the expander
EXP.BYP OFF/ON Bypasses the expander
LIM.THRE –12.0 dB to 0.0 dB Threshold of the limiter