User Manual
Table Of Contents
- Como usar este Manual de Referência
- Sumário
- Árvore de funções
- Seção SELECTED CHANNEL (canal selecionado)
- Seção Channel Strip (Seção de cada canal)
- Patch de entrada e saída
- Canais de entrada
- Fluxo do sinal para canais de entrada
- Como especificar o nome do canal, o ícone e a cor do canal
- Definindo as configurações do HA (amplificador de entrada)
- Emissão do sinal de um canal de entrada para o barramento STEREO/MONO
- Função de panorâmica adicionada (apenas canais de entrada mono)
- Envio de um sinal de um canal de entrada para um barramento MIX/MATRIX
- Indicação no visor do nome do canal
- Correção do atraso entre os canais (Input Delay)
- Saída surround para canais de entrada
- Operações da biblioteca de canais
- Canais OUTPUT
- Fluxo do sinal para canais de saída
- Como especificar o nome do canal, o ícone e a cor do canal
- Envio de sinais dos canais MIX para o barramento STEREO/MONO
- Envio de sinais dos canais MIX e STEREO/MONO para barramentos MATRIX
- Corrigindo o atraso entre os canais (Output Delay (atraso de saída))
- Uso da função PORT TO PORT
- Operações da biblioteca de canais
- EQ (equalizador) e dinâmica
- Trabalho de canal
- Memória de cena
- Armazenando e recuperando cenas
- Edição de memórias de cena
- Uso da função Global Paste
- Uso da função Focus Recall
- Uso da função Fade
- Emitindo um sinal de controle para um dispositivo externo juntamente com a chamada de cena (GPI OUT)
- Reproduzindo um arquivo de áudio vinculado a uma chamada de cena
- Uso do modo de visualização
- Funções Monitor e Cue
- Talkback e Oscilador
- Meters
- EQ gráfico, EQ paramétrico, efeitos e Premium Rack
- Dispositivos de E/S e os amplificadores principais externos
- Usando um dispositivo de E/S
- Como controlar remotamente uma unidade da série R
- Função de controle HA adicionada do equipamento de terceiros
- Como controlar remotamente um amplificador
- Controle remoto da unidade WIRELESS
- Usando um amplificador de entrada externo
- Controlando remotamente um amplificador de entrada externo
- Controle de um amplificador de entrada externo
- MIDI
- Gravador
- Controle AFC IMAGE
- Instalação
- Sobre a tela SETUP
- Preferências
- Teclas USER DEFINED
- Funções que podem ser atribuídas às teclas USER DEFINED
- Botões giratórios USER DEFINED
- Funções que podem ser atribuídas aos botões giratórios USER DEFINED
- Banco de faders personalizados
- Console Lock
- Salvando e carregando dados de configuração de uma unidade flash USB
- Função de remontagem adicionada a unidades flash USB
- Configurações do Word Clock e dos compartimentos
- Usando conexões em cascata
- Configurações básicas dos barramentos MIX e MATRIX
- Como ligar/desligar toda a fonte de alimentação phantom
- Como especificar o brilho da tela sensível ao toque, LEDs, visores de nome de canal e lâmpadas
- Definição da data e da hora do relógio interno
- Configuração do endereço de rede
- Configurando a rede de áudio Dante
- Dante Device Lock
- Compatibilidade com o Dante Domain Manager
- Uso da GPI (General Purpose Interface)
- Função Help
- Outras funções
- Inicializando a unidade com as configurações padrão de fábrica
- Ajustando o ponto de detecção da tela sensível ao toque (função Calibration (calibração))
- Ajustando os faders (função Calibration)
- Fazendo ajustes finos no ganho de entrada e saída (função Calibration)
- Ajuste da cor do LED (função Calibration)
- Como ajustar o brilho do visor de nome do canal
- Como ajustar o contraste do visor de nome do canal
- Inicializando as configurações da rede de áudio Dante
- Procedimento de atualização alterado para o firmware NAME SUB CPU
- Função de atualização adicionada ao firmware Dante
- Mensagens de advertência/erro
- Índice
- Data List
Data List
20
M.BAND COMP
Two input, two output 3-band compressor, with individual solo and gain reduction metering for
each band.
Premium Rack Processor Parameters
Portico5033
This models an analog 5-band EQ made by the RND company.
Portico5043
This models an analog compressor/limiter made by the RND company.
LIM.ATK 0–120 ms Attack time of the limiter
LIM.REL
*1
Release time of the limiter
LIM.KNEE 0–5 Knee of the limiter
LIM.BYP OFF/ON Bypasses the limiter
PRESENCE –10 to +10
Positive (+) values lower the threshold of the high band and raise the
threshold of the low band. Negative (–) values do the opposite. If this is
set to 0, the high, mid, and low bands will be affected in the same way.
LOOKUP 0.0–100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz)
Parameter Range Description
L-M XOVER 21.2 Hz–8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz–8.00 kHz Crossover frequency between the mid and high bands
SLOPE –6 dB, –12 dB Filter slope
LOW GAIN –12.0 dB to +12.0 dB Low band gain
MID GAIN –12.0 dB to +12.0 dB Mid band gain
HI. GAIN –12.0 dB to +12.0 dB High band gain
TOTAL –72.0 dB to +12.0 dB Overall gain
CEILING –6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
LOW THRE –54.0 dB to 0.0 dB Threshold of the low band compressor
LOW RAT 1:1 to 20:1 Ratio of the low band compressor
LOW ATK 0–120 ms Attack time of the low band compressor
LOW REL
*1
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz)
Release time of the low band compressor
LOW KNEE 0–5 Knee of the low band compressor
LOW BYP OFF/ON Bypasses the low band compressor
MID THRE –54.0 dB to 0.0 dB Threshold of the mid band compressor
MID RAT 1:1 to 20:1 Ratio of the mid band compressor
MID ATK 0–120 ms Attack time of the mid band compressor
MID REL
*1
Release time of the mid band compressor
MID KNEE 0–5 Knee of the mid band compressor
MID BYP OFF/ON Bypasses the mid band compressor
HI. THRE –54.0 dB to 0.0 dB Threshold of the high band compressor
HI. RAT 1:1 to 20:1 Ratio of the high band compressor
HI. ATK 0–120 ms Attack time of the high band compressor
HI. RAT
*1
Release time of the high band compressor
HI. KNEE 0–5 Knee of the high band compressor
HI. BYP OFF/ON Bypasses the high band compressor
LOOKUP 0.0–100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
Parameter Range Description
Parameter Range Description
ALL BYPASS OFF, ON
Turns bypass on/off for the EQ. Even in the bypassed state, the signal will
pass through the input/output transformers and the amp circuit.
TRIM –12.0 to 12.0 dB Input gain
LF FREQ 30.00 to 300.0 Hz Center frequency of the LF band
LF GAIN –12.0 to 12.0 dB Gain of the LF band
LMF IN OFF, ON Switches the LMF band on/off
LMF Q 0.70 to 5.00 Q of the LMF band
LMF FREQ 50.00 to 400.0 Hz Center frequency of the LMF band
LMF GAIN –12.0 to 12.0 dB Gain of the LMF band
MF IN OFF, ON Switches the MF band on/off
MF Q 0.70 to 5.00 Q of the MF band
MF FREQ 330.0 to 2500 Hz Center frequency of the MF band
MF GAIN –12.0 to 12.0 dB Gain of the MF band
HMF IN OFF, ON Switches the HMF band on/off
HMF Q 0.70 to 5.00 Q of the HMF band
HMF FREQ 1.80k to 16.0k Hz Center frequency of the HMF band
HMF GAIN –12.0 to 12.0 dB Gain of the HMF band
LF/HF IN OFF, ON Switches the LF/HF bands on/off
HF FREQ 2.50k to 25.0k Hz Center frequency of the HF band
HF GAIN –12.0 to 12.0 dB Gain of the HF band
Parameter Range Description
IN OFF, ON
Turns bypass on/off for the compressor. When bypassed, the button will
be unlit. However even in the bypassed state, the signal will pass through
the input/output transformers and the amp circuit.
FB OFF, ON Switches between feed-forward type and feed-back type
THRESHOLD –50.0 to 0.0 dB Threshold level
RATIO 1.10 : 1 to 28.9 : 1, LIMIT Compression ratio
ATTACK 20 to 75 ms Attack time
RELEASE 100 ms to 2.50 sec Release time
GAIN –6.0 to 20.0 dB Output level