User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
199
*1) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1L-ST IN 8R, MIX1-MIX16, MTRX1-MTRX8, ST L, ST R, MONO
*2) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1-ST IN 8, MIX1-MIX16, MTRX1-MTRX8, STEREO, MONO(C)
*3) MIX1-MIX16, MTRX1-MTRX8, ST L, ST R, MONO
*4) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1-ST IN 8, MIX1-MIX16, MTRX1-MTRX8, STEREO, MONO(C),
DCA1-DCA16
*5) QL5: INPUT25/26-31/32, QL1: INPUT9/10-15/16
SELECTED CH, QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1L-ST IN 8R
*6) MIX1-6, EXT5.1 1, EXT5.1 2, EXT5.1 3, EXT ST 1, EXT ST 2, EXT ST 3, EXT ST 4, MIX1/2, MIX3/4, MIX5/6,
MIX7/8, MIX9/10, MIX11/12, MIX13/14, MIX15/16, MATRIX1/2, MATRIX3/4, MATRIX5/6, MATRIX7/8, STEREO,
MONO, PB OUT
USER DEFINED knobs
This section explains how to assign the desired functions to the USER DEFINED knobs in the
lower part of the touch screen, and to press these knobs to execute the defined function.
If you are logged-in as a user, you can make USER DEFINED knob settings for the user. If
you are logged-in as the Administrator, you can also make the USER DEFINED knob settings
for the Guest account.
NOTE
For details on the assignable functions and their parameters, refer to “Functions that can be
assigned to USER DEFINED knobs” on page 200.
TALKBACK
DIRECT ASSIGN WITH
ON
*3)
The operations performed when this key is
pressed are as follows.
- Assignments other than for the channel
selected in list 3) are removed.
- If a channel is assigned and TALKBACK is ON at
the same time, TALKBACK is turned OFF and
the channel assignment is removed.
- Otherwise, TALKBACK will be ON and the
channel assignment will be ON.
At this time, the LED display is as shown below.
- If the channel is assigned and TALKBACK is ON
at the same time, the LED will be on.
- Otherwise, the LED will be off.
TAP TEMPO
CURRENT PAGE —
Use the tap tempo function in the displayed
screen.
EFFECT RACK1-8
WITH POPUP Use the tap tempo function for the specified
effect. If WITH POPUP is selected, the Tap
Tempo screen is displayed. If WITHOUT POPUP
is selected, the Tap Tempo screen is not
displayed.
WITHOUT POPUP
USER
DEFINED
KEYS
BANK SELECT
BANK A
When selected, the lamp for the corresponding
key comes on.
BANK B
When selected, the lamp for the corresponding
key comes on.
BANK C
When selected, the lamp for the corresponding
key comes on.
BANK D
When selected, the lamp for the corresponding
key comes on.
PREVIOUS BANK
Switches to the previous bank. If the current
bank is BANK A, it switches to BANK D.
NEXT BANK
Switches to the next bank. If the current bank is
BANK D, it switches to BANK A.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER DEFINED KNOBS tab.
4. Press the button corresponding to the USER DEFINED knob to which you want to
assign a function.
5. In the USER DEFINED KNOB SETUP window, make sure that the FUNCTION field is
enclosed by a frame, then select the function that you want to assign.
6. If the selected function has parameters, press the PARAMETER 1 or 2 field to move
the frame, then select parameters 1 and 2 in the same way.
7. Press the OK button to close the USER DEFINED KNOB SETUP window.
8. To execute an assigned function, press the corresponding USER DEFINED [1]-[4]
knob in the lower part of the touch screen, then operate the [TOUCH AND TURN]
knob.
USER SETUP window
(USER DEFINED KNOBS page)
USER DEFINED KNOB SETUP window