V1.3 ユーザーガイド JA MonitorMix V1.
はじめに このたびは、iOS、Android 用アプリケーション「MonitorMix」をダウンロードいただきありがとうございます。 「MonitorMix」は、RIVAGE PM/CL/QL/TF シリーズの MIX/MATRIX/AUX ミックスをワイヤレスでコントロールできます。MonitorMix は最大 10 台まで同時に使用でき、各演奏者が手元で自分のモニターミックスを作ることができます。その際は自分用に割り当てられた MIX/ MATRIX/AUX バスのバランスだけが操作対象となるので、他の演奏者へのモニターミックスを誤って操作してしまう心配もありません。 ご注意 • このソフトウェアおよび取扱説明書の著作権はすべてヤマハ株式会社が所有します。 • このソフトウェアおよび取扱説明書の一部または全部を無断で複製、改変することはできません。 • このソフトウェアおよび取扱説明書を運用した結果およびその影響については、一切責任を負いかねますのでご了承ください。 • 市販の音楽 / サウンドデータは、私的使用のための複製など著作権法上問題にならない場合を除いて、権利者に無断で複製または転用することを
目次 はじめに 2 ご注意............................................................................................ 2 動作環境 4 Wi-Fi の設定 4 準備 5 ミキサーのネットワークの設定................................................... 5 スマートデバイスの Wi-Fi 設定................................................... 5 MonitorMix の設定 8 各部の名称と機能 12 ツールバー................................................................................... 12 FADER 画面...............................................................................
動作環境 OS iOS 11.0 以降、Android 6 以降 ハードウェア iPhone5S 以降、iPod touch 6th 以降、iPad Air 以降 Android 版は、Nexus5/6/7(2013)/9/5X/6P を推奨 対応ミキサーとファームウェア ヤマハ RIVAGE PM シリーズ V4.00 以降、CL/QL シリーズ V4.00 以降、TF シリーズ V1.12 以降 Wi-Fi の設定 各機器の取扱説明書に従って、Wi-Fi アクセスポイントを設定してください。特別な設定は必要ありませんが、外部からネットワークへの侵入 を防ぐために WPA2 のようなセキュリティをかけていただくことをおすすめします。 以下の設定を参考にしてください。 1. Wi-Fi ネットワーク上で名前を設定します(これが「SSID」となります)。 2. セキュリティモード(例:WPA2)とパスワードを設定します。 3. ワイヤレスモードを選択します(802.11n または 802.11ac)。 4.「n」の場合、ワイヤレスバンドを選択します(2.4GHz または 5GHz)。 5.
準備 ミキサーのネットワークの設定 1. CAT5 ケーブルを使って、ミキサーのネットワークポートと Wi-Fi アクセスポイントを接続します。 AUTO-MDI/MDI-X 機能のない古いアクセスポイントに接続するときは、クロスケーブルが必要になります。最近の機器の多くは AUTOMDI/MDI-X 機能をサポートしていますので、その場合はストレートケーブル、クロスケーブルいずれも使用できます。 2. イーサネットケーブルが Wi-Fi 機器の LAN ポートに接続されていることを確認してください。 (WAN ポートには接続しないでください。) スマートデバイスの Wi-Fi 設定 DHCP または固定 IP アドレスを使って、スマートデバイスの設定をします。 1. ホーム画面の [ 設定 (Settings)] アイコンをタップする。 2. [Wi-Fi] を選択する。 MonitorMix V1.
3. 有効な Wi-Fi アクセスポイントの一覧から、接続したい Wi-Fi アクセスポイントをタップする。 4. パスワードを求められた場合は、パスワードを入力する。 5. iOS の場合は Wi-Fi アクセスポイントの [Information] ボタン をタップする。 Android の場合は、パスワードを入力する画面にある [Advanced options] ボタンをタップする。 MonitorMix V1.
6. [DHCP]、または [Static](固定 IP アドレス)を選択する。 Static を選択した場合は下記のように設定します。 IP Address ミキサーの IP アドレスの第 4 オクテットのみを変えた IP アドレスを入力(例: ミキサーの IP アドレスが 「192.168.0.128」の場合、スマートデバイスには「192.168.0.127」のように入力します。) Subnet Mask 「255.255.255.
MonitorMix の設定 アイコンをタップして MonitorMix を起動します。 SELECT MIXER 画面が表示されます。この画面では以下のようなことができます。 • オフラインデモモードに入り、MonitorMix の機能やユーザーインターフェースを試すことができます。 • ネットワーク内にあるミキサーを選択し、MonitorMix を開始します。 オフラインデモモード SELECT MIXER 画面で [Offline Demo] をタップすると、ミキサーと MonitorMix が接続されていない(オフライン)状態でも、アプリケーショ ンの使い方を確認できます。ただし、このモードではレベルメーターは表示せず、TF5 の AUX9/10 に接続しているものと仮定して動作します。 また、グループの編集(16 ページ)はできますが、保存されません。 ミキサーの選択と動作の開始 SELECT MIXER 画面のリストからミキサーを選択して [Connect] を タップします。 MonitorMix V1.
ミキサーに接続されている MonitorMix がすでに最大数(合計 10 台) に達している場合は、IP Address の左横に禁止マークが表示されます。 また、禁止マークが表示されているミキサーを選んで [Connect] ボタ ンを押すと、接続できなかったことを示すメッセージが表示されます。 MonitorMix がミキサーからバスの情報を取得する処理が終わると、 SELECT AUX 画面(TF シリーズ)、または SELECT MIX/MATRIX 画面(RIVAGE PM/CL/QL シリーズ)が表示されます。 自分のモニターミックスに使用されるバスをリストから選択します。 [Done] をタップするとデータの同期を開始します。[Cancel] をタップ すると、SELECT MIXER 画面に戻ります。 データの同期が終わったら、FADER 画 面が表示され、MonitorMix の準備が完了します。 MonitorMix V1.
PIN の設定と運用 各演奏者が自分以外のモニターミックスを誤って操作するのを防ぐために、ミキサーに PIN(Personal Identification Number)を設定して 運用できます。 PIN の設定 PIN の設定と変更は、あらかじめミキサー側で行なっておきます。 ミキサーの SETUP 画面→ NETWORK 画面にある「PIN for MonitorMix」で設定します。 ミキサーで PIN を設定したあと、MonitorMix の SELECT MIXER 画 面で、PIN が設定されたミキサーを選択すると PIN 認証画面が表示さ れます。 ミキサーで設定した PIN が正しく入力されると SELECT AUX 画面が 表示されます。誤った PIN が入力されるとエラーメッセージが表示され ます。 ミキサー側で PIN を設定していない場合は、PIN 認証画面は表示され ずそのまま SELECT AUX 画面に移動します。 MonitorMix V1.
PIN の運用 PIN の運用例は下記のとおりです。いずれの場合も、PIN を各演奏者には知らせずに運用します。 例 1. ミキサーエンジニアが演奏者用のスマートデバイスを用意す る場合 ミキサーエンジニアがあらかじめスマートデバイスに MonitorMix をイ ンストールして、Wi-Fi 設定、PIN の設定、演奏者用のバス選択を完了 しておきます。 演奏者は MonitorMix が起動した状態でスマートデバイスを受け取り、 モニターミックスを調整します。起動していない状態で演奏者が受け 取ったときは、SELECT MIXIER 画面で [Resume] ボタンをタップす ると、以前設定された PIN とバスで自動的に接続されます。 例 2.
各部の名称と機能 ツールバー 画面の切り替えやシーンの情報を表示します。 1 2 3 4 5 6 1 [FADER/PAN] ボタン 3 [ONLINE/OFFLINE] ボタン タップ す る た び に FADER 画 面(13 ペ ー ジ ) と PAN 画 面(15 ページ)を切り替えます。 モニター対象のバスがモノラルの場合は、このボタンは表示されま せん。 ミキサーとの接続状況を表示します。 オンラインのときにタップすると、ミキサーとの接続を切断する確 認メッセージが表示されます。 「No」をタップすると切断せずに確 認メッセージが閉じます。 「Yes」をタップすると切断して SELECT MIXER 画面が表示されます。 オフラインのときにタップするとそのまま SELECT MIXER 画面が 表示されます。 2 [Hide Unused Channels] ボタン SETTINGS 画面にある「Hide Unused Channels button behavior」 の設定に従って、このボタンがオンのときに該当チャンネルが非表示 になります。オフのときは、すべてのチャン
FADER 画面 1 3 各インプットチャンネルからの自分のモニターバスへのセンドレベルを 調整します。 1 チャンネルフェーダー 各インプットチャンネルからのセンドレベルを調節します。フェーダーの 可動域のどの部分をドラッグしても操作できます。ドラッグ中に、操作 しているチャンネルフェーダーの領域外に移動して上下にドラッグする と、より細かい単位で調節できます。 NOTE モニターバスが FIXED に設定されている場合は、センドレベルの編集ができません。 2 チャンネル / バス情報表示 各チャンネルとモニターバスのナンバー、ネーム、カラー、アイコンが 表示されます。このアイコンを長押しすると、チャンネルやバスのオン / オフを切り替えできます。オフの場合はグレー表示になります。 2 チャンネルオフ チャンネルをグループ化したときに作成されるグループマスターチャン ネルには、グループアイコンが表示されます。タップするとグループ化 されているチャンネルの表示 / 非表示を切り替えできます。グループ化 は PERSONAL GROUP & ORDER 画 面(16 ペ ー ジ ) で 設 定
グループ化されたチャンネルの操作 グループ化されたチャンネルは、グループマスターチャンネルに格納さ れ、グループアイコンをタップすることで表示 / 非表示を切り替えでき ます。チャンネルごとにレベルのバランスを調整したあと、グループマ スターチャンネルでグループ全体のレベルを調整します。グループマス ターチャンネルでは、グループ化されたチャンネルの相対的なレベルバ ランスを保持したまま全体のレベルを操作できます。 チャンネル の グル ープ化 は PERSONAL GROUP & ORDER 画 面 (16 ページ)で設定します。 グループマスターチャンネル MonitorMix V1.
PAN 画面 1 2 各インプットチャンネルの、自分のモニターバスでのパン / バランスを 設定します。 PAN 画面は、モノラルバスでは表示されません。 1 PAN コントロールバー バーの領域を上下にドラッグして、各チャンネルの PAN を操作します。 ダブルタップするとセンター位置になります。 PAN の位置はオレンジ色のバーで表示されます。また、センター位置 は緑色の線で表示されます。 ステレオチャンネルの場合は、ミキサー側の PAN モードと BALANCE モードの切り替えによって動作が変わります。 PAN モードの場合は L チャンネルと R チャンネルそれぞれ独立して PAN の調整ができます。 BALANCE のモードの場合は、L チャンネルと R チャンネルの PAN 位置が常に連動します。 NOTE • 自分のモニターバスの Pan Link が有効になっている場合は、PAN 画面は表示さ れますが PAN の操作はできません。ただし、TF シリーズの場合、Pan Link が 有効になっていても、STIN/FXRTN チャンネルの PAN は操作できます。 • 自分のモニター
PERSONAL GROUP & ORDER 画面 7 1 6 グループに含めるチャンネルの編集や各チャンネルの並び替えなどを行 ないます。 1 チャンネル表示 タップするとチャンネルを選択します。チャンネルを長押ししてドラッグ すると、チャンネルの表示順を入れ替えしたり、すでにグループ化され ているチャンネル群に追加したりできます。 左右にスワイプすると表示をスクロールします。 2 [Group] ボタン 選択したチャンネルをグループ化します。タップするとグループマスター チャンネルの情報を編集する GROUP NAME 画面が表示されます。 グループマスターチャンネルでは、グループ化されたチャンネルの相対 的なレベルバランスを保持したまま全体のレベルを操作できます。 2 3 4 5 3 [Ungroup] ボタン グループ化されているチャンネルをグループから解除します。 グループマスターチャンネルを選択してタップすると、グループにある すべてのチャンネルが解除されます。 グループマスターチャンネルを展開して、個別のチャンネルを選択して タップすると、選択したチャンネルだけが解除されま
6 [Done] ボタン 7 1 6 PERSONAL GROUP & ORDER 画面を閉じて FADER 画面に戻り ます。 7 [Share] ボタン PERSONAL GROUP & ORDER 画面で設定した内容を、 MonitorMix がインストールされているほかのスマートデバイスに送信 して共有します。 共 有の方法は、Mail、AirDrop (iOS)、Bluetooth (Android) から選 択します。 Mail を選択したときは、デバイスのメールソフトが起動して、設定ファ イル ( 拡張子 .xml) を添付ファイルとして送信できます。 NOTE 2 3 4 5 iTunes (iOS)、USB ファイル共有(Android)でも設定を共有できます。 MonitorMix V1.
GROUP NAME 画面 カラーボタン アイコンボタン グループの情報を編集します。 [Group] ボタンや [Edit] ボタンを押したときは、グループの名前を入れ る画面が表示されます。 カラーボタンをタップすると、グループチャンネルのカラーを選択する 画面が表示されます。 アイコンボタンをタップするとグループチャンネルのアイコンを選択す る画面が表示されます。 MonitorMix V1.
SETTINGS 画面 ユーザー設定やバージョン情報の確認をします。 設定した内容は、インストールしたデバイスに保存され、MonitorMix を終了しても保持されます。 1 Fader Cap フェーダーのつまみの表示 / 非表示を切り替えます。 1 2 3 4 2 Fader Sensitivity 5 フェーダーの領域をドラッグしたときの感度を設定します。初期値は x0.5(指でドラッグした距離の半分)です。x0.1 に設定すると、指で ドラッグした距離の 10 分の 1 動きます。 設定範囲 : x0.1 ~ x0.5(初期値)~ x1.
ABOUT 画面 ソフトウェアのバージョン情報やソフトウェアライセンスを表示します。 License は、オープンソースソフトウェアを使用していないバージョン では表示されません。 MonitorMix V1.
困ったときは SELECT MIXER 画面で接続先のミキサーが表示されない • 準備(5 ページ)を参照して、ミキサーの設定、Wi-Fi の設定、スマートデバイスの設定を確認してください。 Manual Development Group ©2016 Yamaha Corporation 2020 年 2 月発行 MW-E0 MonitorMix V1.