manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Help function
V5 Reference Manual
264
Using USER DEFINED keys to recall Help directly
Assigning the Help function to USER DEFINED keys
Recalling the HELP window using only a USER DEFINED key
Press the USER DEFINED key to which the Help function is assigned. The HELP window will
appear. To close the window, once again press the USER DEFINED key to which the Help
function is assigned.
Directly recalling the Help for a specific panel controller
While holding down the USER DEFINED key to which you have assigned the Help function,
press (or rotate) the panel controller for which you want to recall Help. If the explanation is
available for the controller, the help for the corresponding item will appear.
To close the window, once again press the USER DEFINED key to which the Help function is
assigned.
NOTE
• Panel controllers (other than the faders will not function as long as you continue holding down
the USER DEFINED key to which the Help function is assigned.
• If there are multiple explanations for the same controller, you can repeat the steps above to
successively display these explanations.
Directly recalling the Help for a specific controller in the LCD screen
While holding down the USER DEFINED key to which you have assigned the Help function,
press the on-screen controller for which you want to recall Help. If the explanation is available
for the controller, the help for the corresponding item will appear.
To close the window, once again press the USER DEFINED key to which the Help function is
assigned.
NOTE
• The on-screen controllers will not function as long as you continue holding down the USER
DEFINED key to which the Help function is assigned.
• If there are multiple explanations for the same controller, you can repeat the steps above to
successively display these explanations.
STEP
1. Load the Help file from your USB flash drive.
2. In the Function Access Area, press the SETUP button.
3. Press the USER SETUP button in the upper left of the SETUP screen.
4. In the USER SETUP window, press the USER DEFINED KEYS tab.
5. In the USER DEFINED KEYS page, press the button corresponding to the USER
DEFINED key to which you want to assign the Help function.
6. In the FUNCTION column, choose “HELP” and press the OK button.
7. Press the “x” symbol to close the USER DEFINED KEYS page.
8. In the Function Access Area, press the SETUP button to close the SETUP screen.
SETUP screen USER SETUP window (USER
DEFINED KEYS page)