manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, effects, and Premium Rack
Reference Manual
134
Inserting an internal effect into a channel
This section explains how to insert an effect into a channel by assigning the input/output of
the internal effect to the input/output of the desired channel (except for a ST IN channel). For
details on editing the effect parameters, refer to “Editing the internal effect parameters” on
page 134.
NOTE
• If you are inserting an effect into a channel that handles a stereo source, assign the R channel
insert-out/insert-in to the R input and output of the effect in the same way as step 3.
• For more information about how to operate the INSERT/DIRECT OUT window, refer to “Inserting
an external device into a channel” on page 18.
• The levels before and after the effect are shown by the input and output meters in the upper right
of the EFFECT EDIT window.
• Adjust the effect send master level and the effect parameters so that the signal does not reach
the overload point at the input or output stage of the effect.
Editing the internal effect parameters
This section explains how to change the effect type and edit the parameters. For a rack in
which an effect is mounted, the following information is shown in the VIRTUAL RACK window.
1 Effect title/type
Displays the effect title, the name of the type that is used, and a graphic. The number
of input and output channels (1 IN/2 OUT or 2 IN/2 OUT) of this effect is also shown.
2 Input/output meters
Indicate the level of the signals before and after the effect.
STEP
1. Follow steps 1–3 described in “Virtual rack operations” on page 119, to mount an
effect in a rack.
2. Press the INPUT PATCH L button in the VIRTUAL RACK window, and select the insert-
out for one of the channels as the input source for the rack (page 119).
3. Press the OUTPUT PATCH L button in the VIRTUAL RACK window, and select the
insert-1in or insert-2in of the same channel as the output destination for the rack
(page 119).
4. Use the Bank Select keys and the [SEL] key to select the channel into which you
inserted the effect.
5. Press the popup button in the INSERT field in the SELECTED CHANNEL VIEW screen.
6. In the INSERT/DIRECT OUT popup window, turn on the INSERT ON/OFF button for
the channel into which you inserted the effect.
7. Display the EFFECT EDIT window again, and select the effect type and edit the effect
parameters.
8. Using the fader of the channel you selected as the rack’s output destination in step
3, adjust the level as appropriate.
STEP
1. Press the rack container in which the effect you want to edit is mounted.
2. To change the effect type, press the effect type field in the EFFECT EDIT window, and
select the effect type in the EFFECT TYPE window.
3. Press a knob in the effect parameter field in the EFFECT EDIT window to select it,
and turn the [TOUCH AND TURN] knob to edit the effect parameters.
4. Edit the settings in the special parameter field as necessary.
1 2