manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
195
Switching banks for USER DEFINED key settings
You can register the USER DEFINED key settings (12 keys for QL series consoles) to a
maximum of four banks.
Use the four BANK SELECT buttons on the left to select a bank.
You can press the CLEAR ALL button on the top right side to clear the content of the selected
bank.
Functions that can be assigned to USER DEFINED keys
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
NO ASSIGN — — No assignment.
ALTERNATE
FUNCTION
LATCH —
Toggle ALTERNATE FUNCTION each time it is
pressed. It goes OFF when the bank is switched.
UNLATCH —
Switch to ALTERNATE FUNCTION only while
pressed. It goes OFF when the bank is switched.
AUTOMIXER
group a OVERRIDE ON —
Apply a fade-in to the channels in group a where
the override button is on, until the level drops to
0 dB (the unity gain). Mute all channels with the
button turned off.
group a PRESET ON —
Switch the channels in group a to the mode
indicated by the mode button (man/auto/mute)
next to the lit preset indicator.
group b OVERRIDE ON —
Apply a fade-in to the channels in group b
where the override button is on, until the level
drops to 0 dB (the unity gain). Mute all channels
with the button turned off.
group b PRESET ON —
Switch the channels in group b to the mode
indicated by the mode button (man/auto/mute)
next to the lit preset indicator.
group c OVERRIDE ON —
Apply a fade-in to the channels in group c where
the override button is on, until the level drops to
0 dB (the unity gain). Mute all channels with the
button turned off.
group c PRESET ON —
Switch the channels in group c to the mode
indicated by the mode button (man/auto/mute)
next to the lit preset indicator.
BRIGHTNESS BANK CHANGE —
Toggle between the brightness settings stored in
A and B.
CH ON SPECIFIC CH *4) Switch the CH ON/OFF.
CH SELECT
INC
—
Increment or decrement the selected channel
number.
DEC
SPECIFIC CH *1) Select a channel from list 1).
CUE
OUTPUT — Switch CUE on/off.
CLEAR CUE — This clears the CUE.
SPECIFIC CH *2) CUE the channel selected from list 2).
CUE MODE —
This function switches the cue mode. In
Surround mode, it toggles between MIX, LAST,
and 5.1 SOLO with each press. When set to
MIX, the lamp is off. When set to LAST, the lamp
is on. When set to 5.1 SOLO, the lamp flashes.
CUE INTERRUPTION —
Switches the CUE INTERRUPTION function on or
off
FADER CUE RELEASE —
Switches the FADER CUE RELEASE function on or
off.
DANTE
INPUT
PATCH LIB
DIRECT RECALL LIBRARY #000-#010
Directly recalls the desired number of the
DANTE INPUT PATCH library. However, it does
not function during a scene recall.