manual

Setup
Reference Manual
197
HOME
SELECTED CH VIEW — Displays the SELECTED CHANNEL VIEW screen.
OVERVIEW — Displays the OVERVIEW screen.
TOGGLE —
Each press of the key will alternately display the
SELECTED CHANNEL VIEW screen and the
OVERVIEW screen.
METER
PEAK HOLD ON —
Turns the meter’s peak hold function on/off. Lit
when on.
SURROUND METER —
For Surround mode, toggle between the
content to be shown in meters displayed in the
Function Access Area. The lamp is off for MIX 1-
6, and on for SURROUND MONITOR.
MIDI
PROGRAM CHANGE PGM 1–128
Transmit the corresponding MIDI message.
For NOTE ON, it goes OFF when the bank is
switched.
CONTROL CHANGE
CC 1–31, 33–95,
102–119
NOTE ON
NOTE ON C-2 (0)
:
NOTE ON G 8 (127)
MONITOR
OUTPUT — Switch the monitor output on/off.
SELECTED CH ASSIGN —
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching. It goes OFF when the
bank is switched.
DIMMER ON —
Enable the dimmer and attenuate the monitor
signal.
SOURCE SELECT
STEREO L/R
Recall the selected signal to the monitor.
MONO (C)
LCR
PB OUT
*5)
DEFINE
SURROUND SOURCE
SELECT
*6)
Recall the selected signal to the surround
monitor.
SURROUND
DOWNMIX
STEREO, MONO
When this function is off (the lamp is off),
the setting returns to 5.1 monitor.
SURROUND SPEAKER
SOLO
When this function is on (the lamp is on),
the SURROUND MONITOR screen opens.
When this function is off (the lamp is off),
the SURROUND MONITOR screen closes.
L, R, C, Ls, Rs, LFE
This functionality is the same as the
SPEAKER MUTE function in the
SURROUND MONITOR screen. When the
SOLO button is on, it functions as a SOLO
key.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
MUTE
MASTER
MUTE GROUP 1
— Switch MUTE GROUP MASTER on/off.:
MUTE GROUP 8
ALL MUTE —
Turns all MUTE GROUP MASTER settings on/off
together.
NUENDO
LIVE
TRANSPORT
GO TO PROJECT START
Operate the transport functions of Nuendo Live.
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
GO TO PROJECT END
CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR —
Clear the peak indicators of the Nuendo Live
screen.
ADD MARKER —
This function executes ADD MARKER of
NUENDO Live.
OSCILLATOR
OSCILLATOR ON — Switch the OSC on/off.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of a
channel to switch the assignment on/off. During
this time, the [SEL] LED will be lit if assign is ON,
or dark if OFF. It goes OFF when the bank is
switched.
DIRECT ASSIGN *1)
Assign the oscillator to the channel selected
from list 1).
PAGE
CHANGE
BOOKMARK —
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Popup
windows can also be memorized. In the case of
a rack, the number of that rack is also
memorized.
BOOKMARK with “SEL” —
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
— Display the previous/next page.
NEXT PAGE
CLOSE POPUP — Close the displayed window.
RECORDER TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Recorder transport functions.
AUTO REC
Shortcut function for STOP  REC  PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation