manual

Setup
Reference Manual
198
RECORDER DIRECT PLAY
NO ASSIGN The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL — Recall the scene of the next existing number.
DEC RECALL — Recall the scene of the previous existing number.
DIRECT RECALL SCENE #000–#300 Directly recall the scene of the specified number.
RECALL UNDO — Execute RECALL UNDO.
STORE UNDO — Execute STORE UNDO.
INC — Select the scene of the next existing number.
DEC —
Select the scene of the previous existing
number.
RECALL — Recall the currently-selected scene.
STORE — Store the current settings.
SEND MODE MIX/MATRIX —
If INPUT or ST IN is selected, switch output bus
channels (MIX, MATRIX) to be displayed in the
SEND field of the SELECTED CHANNEL VIEW
screen.
SENDS ON
FADER
MIX1–MIX16
NORMAL/WITH CUE
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH CUE
option, cue will be enabled if SENDS ON FADER
mode is engaged or if you switch mode during
SENDS ON FADER mode. Also, with the WITH
CUE option, cue for all output channels will be
canceled if SENDS ON FADER mode is
disengaged.
MTRX1–MTRX8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL
SET [+48V]
—
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If SET [PRE SEND] is selected, “SEND ON FADER”
mode is engaged while you are holding down
the [SEL] key.
It goes OFF when the bank is switched.
SET [
Ø]
SET [INSERT ON]
SET [DIRECT OUT ON]
SET [PRE SEND]
SET [TO STEREO]
SET [TO MONO]
SET [TO LCR]
SET [GAIN
COMPENSATION]
SET[AUTOMIXER
AUTO/MAN]
SET DEFAULT
VALUE
——
While holding down this key, press SELECTED
CH or the [TOUCH AND TURN] knob to reset it
to the default value. It goes OFF when the bank
is switched.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
SET
NOMINAL
VALUE
——
While holding down this key, press a [SEL] key to
set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
SURROUND
PAN
L ON
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
R ON
C ON
LFE ON
Ls ON
Rs ON
PANNING L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING R
PANNING Front Center
PANNING Ls
PANNING Rs
PANNING Back
PANNING Side L
PANNING Side R
PANNING Center
PANNING TOGGLE *5)
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center  L  Front Center  R
 Side R  Rs  Back, Ls  Side L  (Center).
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
DIRECT ASSIGN *3)
The operations performed when this key is
pressed are as follows.
- Toggle assignment of channel selected in list 3)
ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on.
Otherwise, the LED will be off.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation