manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
200
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the SOFTWARE USER DEFINED KNOBS for Guest page and make USER DEFINED knob
settings for the Guest account.
• The four buttons in the SOFTWARE USER DEFINED KNOBS page correspond to USER
DEFINED knobs [1]–[4] in the lower part of the touch screen. The name of the function or
parameter assigned to each knob appears to the right of the corresponding button. If nothing is
assigned to the knob, an indication of “---” will appear next to the button.
• The list shown in the USER DEFINED KNOB SETUP window is the same for all models of the QL
series.
For the QL1, the display will indicate “Cannot Assign!” if you specify a parameter that does not exist
on that model.
• If there are no parameters for the registered USER DEFINED key, nothing will occur when the key
is operated.
About TOUCH AND TURN
You can press a desired knob in the touch screen and then use the
[TOUCH AND TURN] knob to immediately operate that on-screen
knob.
At this time, a pink frame is shown around the knob in the touch
screen, indicating that you can operate that knob.
Functions that can be assigned to
USER DEFINED knobs
Function PARAMETER 1 PARAMETER 2
NO ASSIGN — —
AUTOMIXER WEIGHT *1)
BRIGHTNESS
LAMP —
PANEL —
SCREEN —
CH COLOR —
NAME —
CUE
INPUT PFL TRIM —
DCA TRIM —
OUTPUT PFL TRIM —
CUE LEVEL —
DIRECT OUT LEVEL LEVEL *14)
DYNAMICS1
THRESHOLD *2)
RANGE *4)
RATIO
*2)
ATTACK
HOLD
*4)
DECAY
RELEASE
*2)OUTGAIN
KNEE
WIDTH *13)
DYNAMICS2
THRESHOLD
*4)
RATIO
FREQUENCY
ATTACK
RELEASE
OUTGAIN
KNEE
WIDTH
EFFECT
Displays the EFFECT RACK No. (1-8) for
the target operation as well as the
name of the mounted EFFECT TYPE or
the name of the GEQ/PEQ TYPE *a).
Displays the names of the 32
parameters for the EFFECT TYPE *b).
Displays “----” if a GEQ/PEQ is
mounted.
EQ
ATT
*2)
LOW Q
LOW FREQUENCY
LOW GAIN
LOW MID Q
LOW MID FREQUENCY
LOW MID GAIN