manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
I/O devices and external head amps
Reference Manual
158
I/O devices and external head amps
This chapter explains how to use an I/O device or an external head amp that is connected to
the QL series console. Before you proceed, use DANTE SETUP to specify the I/O devices
that will be mounted. For details, refer to “Mounting an I/O device on the Dante audio network”
on page 240.
Using an I/O device
QL series consoles enable you to remotely control channel parameters of an I/O device (such
as an R series product) connected to the Dante connector.
For details on connecting the QL series console to an I/O device, refer to the “Connecting to
I/O devices” section in the separate Owner’s Manual.
I/O device patching
Here’s how an I/O device connected to the Dante connector can be patched to the Dante
audio network.
I/O DEVICE screen (DANTE PATCH page)
1 I/O device list
This shows the ID number and model name of the I/O devices.
Press here to access the OUTPUT PATCH window, where you can specify patching from
the console’s output ports to the I/O devices. If a previously set-up device does not
currently exist on the DANTE audio network, a yellow “VIRTUAL” indicator is shown at
the lower left of that device. If devices on the network belong to different DEVICE TYPEs
but share the same ID, a red “CONFLICT” indicator will appear to the left, below the
device. If multiple devices share the same ID, a yellow “DUPLICATE” indicator will
appear to the right, below the device.
2 DANTE SETUP button
Press this button to open the DANTE SETUP window, in which you can make settings
for the audio network.
3 DANTE INPUT PATCH button
Press this button to open the DANTE INPUT PATCH window, in which you can select the
64 channels (32 channels for the QL1) that will be input from the I/O device to the
console.
4 OUTPUT PORT SETUP button
Press this button to access the PATCH VIEW 1 tab of the OUTPUT PORT window, where
you can choose the 64 channels (32 channels for the QL1) that will be output from the
console’s output ports to I/O devices.
STEP
1. Connecting QL series consoles and I/O devices.
For details, refer to the “Connecting to I/O devices” and “Quick Guide” sections in the
separate Owner’s Manual.
2. In the function access area, press the I/O DEVICE button.
3. Press the DANTE PATCH tab in the upper part of the I/O DEVICE screen.
4. Press the DANTE INPUT PATCH button in the I/O DEVICE screen (DANTE PATCH
page).
5. Press the AUTO SETUP button.
If you want to edit individual patches, press the port select button.
6. Press the device in the I/O DEVICE screen (DANTE PATCH page).
7. Press the port select button in the OUTPUT PATCH window.
8. In the PORT SELECT screen, select the output port.
1
2
3
4