manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
205
• WITH SEND ........................ Restricts operation of that channel’s send parameters.
(From MIX, From MATRIX)
• DCA MASTER .................... Restricts operation of that channel’s DCA group fader,
ON/OFF, and ICON/COLOR/NAME.
• DCA GROUP ASSIGN........ Restricts changes of assignment to that DCA group.
• SET BY SEL ....................... If this button is on, you can press the panel [SEL] key of
a channel to enable or disable the above-mentioned
operating restrictions for that channel.
2 CURRENT SCENE
Specifies the operations that can be performed on the current scene memory.
• INPUT PATCH/INPUT NAME
..................... Restricts operations for input channel patching and
names.
• OUTPUT PATCH/OUTPUT NAME
..................... Restricts operations for output channel patching and
names.
• BUS SETUP........................ Restricts operations for bus setup.
• GEQ RACK/EFFECT RACK/PREMIUM RACK
..................... Restricts operations for the racks. Press this area to open
the RACK USER LEVEL window, in which you can set
this restriction.
However, there will be no restriction on operating the
MIDI CLK button displayed for delay-type and
modulation-type effects, or the PLAY/REC button
displayed for the FREEZE effect.
• MUTE GROUP ASSIGN/MUTE GROUP MASTER
..................... Restricts operations for mute group assignment and
mute group master.
NOTE
In the case of the QL1, faders that do not exist on the model will not be shown.
3 SCENE LIST
Specifies the operations that can be performed on scene memories.
• STORE/SORT operations
• RECALL operations
4 LIBRARY LIST
Specifies the operations that can be performed on libraries.
• STORE/CLEAR operations
• RECALL operations
5 FILE LOAD
Specifies the settings that will be applied when a file is loaded from a USB flash drive.
The user authentication key contains settings such as the user level, preferences, and the
USER DEFINED key settings (USER SETUP settings). Other data is saved in an “ALL” file.
The “ALL” file also includes the USER SETUP settings of the Administrator and the Guest.
• USER SETUP (Preference and USER DEFINED keys settings)
• SYSTEM SETUP/MONITOR SETUP
• CURRENT SCENE
• SCENE LIST
•LIBRARY LIST
6 MONITOR SETUP
Specifies the monitor setup operations that can be performed.
•OSCILLATOR
• TALKBACK
•SOLO
7 SYSTEM SETUP
Specifies the system setup operations that can be performed.
• MIXER SETUP
• OUTPUT PORT
• MIDI/GPI
• DANTE SETUP
NOTE
• The content that is restricted with the DANTE SETUP button is as shown below.
• Changing the CONSOLE ID
• Changing the SECONDARY PORT setting
• Changing control of DANTE PATCH changes (THIS CONSOLE or DANTE CONTROLLER)
• Changing BIT DEPTH
• Changing LATENCY
• Changing DEVICE MOUNT
• Changing REMOTE HA ASSIGN
• Changing the Dante Input Patch
• Changing the Dante Output Patch
• Changing the Dante Input Patch Library (Changing Store, Recall, Clear, Library Name)
• Changing the PREFERED MASTER
• If an operation is restricted, the message “This operation is not allowed.” is displayed at the
bottom of the screen.
• With the factory settings, this is turned off (no restrictions).
8 SET ALL/CLEAR ALL button
Permits/clears all items.