manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
212
NUENDO
LIVE
TRANSPORT
GO TO PROJECT START
Operate the transport functions of Nuendo Live.
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
GO TO PROJECT END
CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR —
Clear the peak indicators of the Nuendo Live
screen.
ADD MARKER —
This function executes ADD MARKER of
NUENDO Live.
OSCILLATOR
OSCILLATOR ON — Switch the OSC on/off.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of a
channel to switch the assignment on/off. During
this time, the [SEL] LED will be lit if assign is ON,
or dark if OFF. It goes OFF when the bank is
switched.
DIRECT ASSIGN *1)
Assign the oscillator to the channel selected
from list 1).
PAGE
CHANGE
BOOKMARK —
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Popup
windows can also be memorized. In the case of
a rack, the number of that rack is also
memorized.
BOOKMARK with “SEL” —
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
— Display the previous/next page.
NEXT PAGE
CLOSE POPUP — Close the displayed window.
RECORDER TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Recorder transport functions.
AUTO REC
Shortcut function for STOP REC PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
RECORDER DIRECT PLAY
NO ASSIGN The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL — Recall the scene of the next existing number.
DEC RECALL — Recall the scene of the previous existing number.
DIRECT RECALL SCENE #000–#300 Directly recall the scene of the specified number.
RECALL UNDO — Execute RECALL UNDO.
STORE UNDO — Execute STORE UNDO.
INC — Select the scene of the next existing number.
DEC —
Select the scene of the previous existing
number.
RECALL — Recall the currently-selected scene.
STORE — Store the current settings.
SEND MODE MIX/MATRIX —
If INPUT or ST IN is selected, switch output bus
channels (MIX, MATRIX) to be displayed in the
SEND field of the SELECTED CHANNEL VIEW
screen.
SENDS ON
FADER
MIX1–MIX16
NORMAL/WITH CUE
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH CUE
option, cue will be enabled if SENDS ON FADER
mode is engaged or if you switch mode during
SENDS ON FADER mode. Also, with the WITH
CUE option, cue for all output channels will be
canceled if SENDS ON FADER mode is
disengaged.
MTRX1–MTRX8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL
+48V
—
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If [PRE SEND] is selected, “SEND ON FADER”
mode is engaged while you are holding down
the [SEL] key.
Press SEL to switch between auto/man if
[AUTOMIXER AUTO/MAN] is selected. It goes
OFF when the bank is switched.
Ø
INSERT ON
DIRECT OUT ON
PRE SEND
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
AUTOMIXER AUTO/
MAN
SET DEFAULT
VALUE
——
While holding down this key, press SELECTED
CH or the [TOUCH AND TURN] knob to reset it
to the default value. It goes OFF when the bank
is switched.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation