Owner`s manual

Setup
Reference Manual
172
*1) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1L-ST IN 8R, MIX1-MIX16, MTRX1-MTRX8, ST L, ST R, MONO(C)
*2) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1-ST IN 8, MIX1-MIX16, MTRX1-MTRX8, STEREO, MONO(C)
*3) MIX1-MIX16, MTRX1-MTRX8, ST L, ST R, MONO(C)
*4) QL5: CH1-CH64, QL1: CH1-CH32, ST IN 1-ST IN 8, MIX1-MIX16, MTRX1-MTRX8, STEREO, MONO(C),
DCA1-DCA16
*5) QL5: INPUT25/26-31/32, QL1: INPUT9/10-15/16
PAGE
CHANGE
BOOKMARK
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Screens can
also be memorized. In the case of a rack, the
number of that rack is also memorized.
BOOKMARK with “SEL” —
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
— Display the previous/next page.
NEXT PAGE
CLOSE POPUP — Close the displayed window.
RECORDER
TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Recorder transport functions.
AUTO REC
Shortcut function for STOP  REC  PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
DIRECT PLAY
NO ASSIGN The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL — Recall the scene of the next existing number.
DEC RECALL — Recall the scene of the previous existing number.
DIRECT RECALL SCENE #000–#300 Directly recall the scene of the specified number.
RECALL UNDO — Execute RECALL UNDO.
STORE UNDO — Execute STORE UNDO.
INC — Select the scene of the next existing number.
DEC —
Select the scene of the previous existing
number.
RECALL — Recall the currently-selected scene.
STORE — Store the current settings.
SEND MODE MIX/MATRIX —
If INPUT or ST IN is selected, switch output bus
channels (MIX, MATRIX) to be displayed in the
SEND field of the SELECTED CHANNEL VIEW
screen.
SENDS ON
FADER
MIX1–MIX16
—
Switches the MIX ON FADER function for the
selected MIX on and off.
MTRX1–MTRX8
Switches the MATRIX ON FADER function for the
selected MATRIX on and off.
MIX ON FADER Switches the MIX ON FADER function on and off.
MATRIX ON FADER
Switches the MATRIX ON FADER function on
and off.
SENDS ON FADER
Switches the SENDS ON FADER function on and
off.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
SET BY SEL
SET [+48V]
—
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If SET [PRE SEND] is selected, “SEND ON FADER”
mode is engaged while you are holding down
the [SEL] key.
SET [
Ø]
SET [INSERT ON]
SET [DIRECT OUT ON]
SET [PRE SEND]
SET [TO STEREO]
SET [TO MONO]
SET [TO LCR]
SET [GAIN
COMPENSATION]
SET[AUTOMIXER
AUTO/MAN]
SET DEFAULT
VALUE
——
While holding down this key, press SELECTED
CH or the [TOUCH AND TURN] knob to reset it
to the default value.
SET
NOMINAL
VALUE
——
While holding down this key, press a [SEL] key to
set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH Turn TALKBACK on while pressed.
SELECTED CH ASSIGN —
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
DIRECT ASSIGN *3)
Assign TALKBACK to the channel selected from
list 3).
TAP TEMPO
CURRENT PAGE —
Use the tap tempo function in the displayed
screen.
EFFECT RACK1–8 —
Use the tap tempo function for the specified
effect.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation