Owner`s manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Data List
40
Input/Output Specifications
Analog input specifications
*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined
level when all the faders and level controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be
turned on/off individually from the console software.
*6. QL1: INPUT1-16
Analog output specifications
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT,
Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the
maximum position.
*7. QL1: OMNI OUT 1-8
Digital input/output specifications
*1. QL1: 32ch Input/32ch Output@48kHz
Digital output specifications
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
I/O SLOT (1-2) specifications
A Mini-YGDAI card can be inserted into slots 1-2.
Only slot 1 supports serial interfaces.
Control I/O specifications
*1. Input pin: TTL level, w/ internal pull-up (47kΩ)
Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA)
Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be
adjusted from the software.
Input
Connectors
Gain
Input
Impedance
Source
Impedance
Input Level
Connector
Sensitivity
*1
Defined Level
Maximum
Non-Clip Level
INPUT 1-32
*6
+66dB
7.5 kΩ
50-600 Ω
Mics &
600 Ω Lines
–82dBu
(61.6μV)
–62dBu
(0.616mV)
–42dBu
(6.16mV)
XLR-3-31
type
(Balanced)
*2
–6dB
–10dBu
(245mV)
+10dBu
(2.45V)
+30dBu
(24.5V)
Output
Connectors
Output
Impedance
Load
Impedance
Maximum
Output
Level SW
*5
Output Level
Connector
Defined Level
Maximum
Non-Clip
Level
OMNI OUT
1-16
*7
75 Ω 600 Ω Lines
+24dB
(default)
+4dBu
(1.23V)
+24dBu
(12.3V)
XLR-3-32 type
(Balanced)
*1
+18dB
–2dBu
(616mV)
+18dBu
(6.16V)
PHONES 15 Ω
8 Ω Phones –
75mW
*6
150mW
Stereo Phone Jack
(TRS)
(Unbalanced)
*2
40 Ω Phones –
65mW
*6
150mW
Connectors Format
Data
Length
Level Audio Connector
Primary/
Secondary
Dante
24bit or
32bit
1000Base-T
64ch Input/64ch Output
@48kHz
*1
etherCON CAT5e
Connectors Format
Data
Length
Level Connector
DIGITAL OUT AES/EBU AES/EBU Professional Use 24 bit RS422
XLR-3-32 type (Balanced)
*1
Connectors Format Level Connector
MIDI
IN MIDI – DIN Connector 5P
OUT MIDI – DIN Connector 5P
WORD CLOCK
IN – TTL/75 Ω terminated BNC Connector
OUT – TTL/75 Ω BNC Connector
GPI (5IN/5OUT) – –
D Sub Connector 15P
(Female)
*1
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
LAMP
(QL5: x2, QL1: x1)
–
0V-12V XLR-4-31 type
*2
USB HOST USB 2.0 – USB A Connector (Female)