Owner`s manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Channel Job
Reference Manual
69
Moving the parameters of a channel
The settings of a specific input channel can be moved to a different input channel. When you
execute a Move operation, the numbering of the channels between the move-source and
move-destination will move forward or backward by one.
You can move settings between the following combinations of channels.
• Between input channels
• Between ST IN channels
CH MOVE MODE window
1 SOURCE CH field
Displays the move-source channel. While this window is displayed, press a [SEL] key on
the top panel to select an input channel. The selected channel will be highlighted in this
field. If you want to re-select the move-source channel, press this field.
2 DESTINATION CH field
Displays the move-destination channel. When you specify the move-source, you can
then select the move-destination input channel by pressing its [SEL] key on the panel.
When the move-destination channel is selected, this field will be highlighted. If you
want to defeat the selected move-destination channel, press the DESTINATION CH field.
NOTE
In the case of the QL1, faders that do not exist on the model will not be shown.
3 MOVE button
Executes a move operation. After selecting the move-source channel and
move-destination channel, the channel settings move from the move-source to the
move-destination. The settings of all channels between the move-source and
move-destination will shift toward the move-source by one channel.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the MOVE button in the CH JOB menu.
3. Press a [SEL] key to select the move-source channel.
4. Press the [SEL] key for the move-destination channel.
5. To execute the move, press the MOVE button.
1 2 3 4 5
1 5 2 3 4
Move by one.
Move
CH JOB
menu
Function
Access Area
1 2
3
4