User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
SELECTED CHANNEL section
Reference Manual
6
SELECTED CHANNEL section
This chapter explains how to use the SELECTED CHANNEL section and the SELECTED CHANNEL
VIEW screen to control the selected channel.
About the SELECTED CHANNEL section
The SELECTED CHANNEL section located to the left of the display corresponds to the mixer module
on a conventional analog mixer, and enables you to manually adjust all the major parameters of the
currently-selected channel.
Operations in this section will affect the channel that was most recently selected by its [SEL] key. If you
have assigned an ST IN channel or STEREO channel to a single channel strip, either the L or the R
channel will be selected, and the major parameters for L and R channels will be linked. You can use the
knobs on the panel to control mix parameters such as head amp gain, HPF/EQ settings, the threshold
setting of the dynamics processors, pan/balance settings, and send levels to the MIX/MATRIX buses.
Operations in the SELECTED CHANNEL section
Follow the steps below to perform operations in the SELECTED CHANNEL section.
1. Use a [SEL] key to select the channel you want to control.
To select a channel, press a [SEL] key in the top panel channel strip section, the Centralogic
section, or the master section.
Press the appropriate bank select key so that the
channels you want to control are assigned to the
top panel.
The number and name of the currently-selected
channel is shown in the channel select field
located in the Function Access Area of the touch
screen.
NOTE
• If an ST IN channel or STEREO channel has
been assigned to a single channel strip, you can switch between L and R by repeatedly pressing
the same [SEL] key.
• You can also switch channels by pressing the channel select field located in the Function Access
Area. Press the left side of the field to select the preceding channel. Press the right side of the
field to select the next channel.
2. Press one of the knobs in the SELECTED CHANNEL section.
Press a knob in the SELECTED CHANNEL section to display the SELECTED CHANNEL VIEW
screen for the currently-selected channel. If you leave this screen displayed, you will always be able
to view the settings in the screen while operating the knobs in the SELECTED CHANNEL
section.
NOTE
If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the
PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),
pressing a knob repeatedly will open or close the popup window (1ch).
Even if a different screen is selected, the knobs in the SELECTED CHANNEL section will always
affect the currently-selected channel. In this case, a window indicating the value of that parameter
will appear on screen when you operate a knob.
3. Use the knobs in the SELECTED CHANNEL section and the buttons on the
SELECTED CHANNEL VIEW screen to edit the parameters of the selected channel.
Channel number
Channel name