Owner’s Manual Keep This Manual For Future Reference.
Contents Accessories PRECAUTIONS................................... 5 • Owner’s Manual • AC power cable • Dante Virtual Soundcard Token leaflet (Please check the package contents.) Introduction .................................... 7 Features .............................................................7 Firmware Updates ..............................................7 Precautions for Rack Mounting ..........................7 Recessed Installation ..........................................
The above warning is located on the top of the unit. L’avertissement ci-dessus est situé sur le dessus de l’unité. Explanation of Graphical Symbols Explication des symboles The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING CAUTION Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards.
Information for Users on Collection and Disposal of Old Equipment Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.
Introduction Introduction Thank you for choosing the Yamaha Rio3224-D/Rio1608-D I/O Rack. The Rio3224-D is a Dante-compatible I/O rack, featuring 32 analog inputs, 16 analog outputs, and 8 AES/EBU outputs. The Rio1608-D is a Dante-compatible I/O rack, featuring16 analog inputs and 8 analog outputs. To take full advantage of the superior functions and performance offered by the Rio3224-D/Rio1608-D, and to extend the useful life of the product, be sure to read this owner’s manual carefully before operation.
About Dante About Dante Recessed Installation D 23 7 89 A BC 456 If you want to recess the front panel surface of the device from the front edge of the rack, you can adjust the position of the rack mount brackets to recess the device by 50mm or 100mm, as shown in the illustration below. EF 01 50 mm 100 mm NOTE When you install the brackets, use the same screws that you just removed. This product features Dante technology as a protocol to transmit audio signals.
Controls and Functions Controls and Functions Front Panel 4 5 6 78 9 0 A 789A BCD 3456 3 EF 1 2 012 B C 3 1 [INPUT] Connectors 1–32 {1–16} These are the XLR-3-31 type analog balanced connectors for the input channels. The input level range is from –62 dBu to +10 dBu. +48V phantom power can be supplied to devices that require it via the input connectors. NOTE The PAD will be switched on or off internally when the gain of the internal head amp is adjusted between +17 dB and +18 dB.
Controls and Functions 6 DIP Switches These switches enable you to specify the settings related to the startup operation of the unit. Set the DIP switches while the power to the unit is turned OFF. Otherwise, the setting will not be effective. Refer to the following for details. The switch illustrations indicate the setting state as follows. Switch Status Represent a status with switch toggled up. Represent a status with switch toggled down.
Controls and Functions • Switches 5 and 6 (REMOTE) When you plan to monitor or control the Rio from a digital mixing console, these switches determine whether to use an Rio-native device (such as a CL series product) or a non-Rio-native device. Information on which devices feature Rio-native support is available at the Yamaha pro audio website product page: http://www.yamahaproaudio.com/products/ Switch Setting Description NATIVE An Rio-native device will control the Rio.
Controls and Functions Rear Panel D E F D [PRIMARY]/[SECONDARY] Connectors The Rio can be connected to other Dante-compatible devices (such as a CL-series product) via these etherCON (RJ45) connectors using standard Ethernet cables (CAT5e or better recommended). If DIP switch 4 on the front panel is set upward (to DAISY CHAIN), audio signals coming into one of these connectors will be output from the other.
About Connections About Connections There are two ways to connect the Rio to a Dante network. NOTE A daisy chain connection is suitable for a simple system with a small number of devices. Use a star network if a large number of devices are connected. Daisy Chain Network A daisy chain is a wiring scheme in which multiple devices are connected together in sequence. In this way, networking is simple and requires no network switches.
About Connections About Dante Controller Initializing the Rio Dante Controller is a software application that allows configuration and audio routing of Dante networks. Use this application if you plan to connect or set up Dante-enabled devices that do not feature Rio-native support. Please download the Dante Controller application from the website listed below. Please note that Dante Controller Version 3.2.1 or later supports Rio. http://www.yamahaproaudio.
Head Amp Control Head Amp Control The Rio head amplifiers can be remotely controlled from a host device, such as a compatible Yamaha digital mixing console. Control from an Rio-native Device The Rio head amplifiers can be controlled remotely from an Rio-native digital mixing console, such as a CL series product. The connected Rio-native device displays the model name and UNIT ID number of the corresponding Rio unit to be controlled.
Troubleshooting Troubleshooting Troubleshooting Symptom The power won’t turn on. The power indicator doesn’t light. The unit is not receiving an input signal. The input level is too low. Cause Possible Solution The power cable is connected improperly. Connect the power cable properly (see page 12). The [POWER] switch is not turned ON. Turn the [POWER] switch ON. If the power still will not come on, refer the problem to your Yamaha dealer. The input cables are not connected properly.
Troubleshooting Messages Errors, warnings, and certain other types of information are displayed via the Rio front panel indicators. Messages are also displayed in the Dante Controller Error Status field. Each indicator lights or flashes as described below: No call-out The indicator is off. Light The indicator remains lit steadily. Flash The indicator continues to flash. Flash x2 The indicator flashes twice cyclically. Flash x3 The indicator flashes three times cyclically.
Troubleshooting Warning Messages Information Messages The indicators will light and/or flash as shown until the cause is resolved. If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed. The indicators will remain lit and/or flashing cyclically to report the status. If the orange [SYNC] indicator is unlit, the unit is operating normally. If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed. SYNC Indicators Description The word clock is not set correctly.
Specifications Specifications General Specifications 44.1kHz 48kHz 88.2kHz 96kHz Internal Sampling Frequency External 44.1kHz +4.1667%, +0.1%, –0.1%, –4.0% ±200ppm 48kHz +4.1667%, +0.1%, –0.1%, –4.0% ±200ppm 88.2kHz +4.1667%, +0.1%, –0.1%, –4.0% ±200ppm 96kHz +4.1667%, +0.1%, –0.1%, –4.0% ±200ppm Signal Delay Less than 3ms INPUT to OUTPUT, connect with CL5 using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz Frequency Response +0.5, –1.
Specifications Analog Input Characteristics Input Terminals GAIN +66dB INPUT 1-16 –6dB +66dB INPUT 17-32*2 –6dB Actual Load Impedance For Use With Nominal 7.5kΩ 7.5kΩ Input Level Nominal Max. before clip 50-600Ω Mics & 600Ω Lines –62dBu (0.616mV) –42dBu (6.16mV) +10dBu (2.45V) +30dBu (24.5V) 50-600Ω Mics & 600Ω Lines –62dBu (0.616mV) –42dBu (6.16mV) +10dBu (2.45V) +30dBu (24.5V) Connector XLR-3-31 type (Balanced)*1 XLR-3-31 type (Balanced)*1 *1. XLR-3-31 type connectors are balanced.
Specifications Dimensions 5.8 350 361.5 (5.7) Rio3224-D 12 232 220 480 5.8 350 361.5 (5.7) Rio1608-D 12 132 144 480 Unit: mm * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.
Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.
