User Manual
Table Of Contents
- ProVisionaire Design
- Contents
- 1. Introduction
- 2. Audio Components
- 2.1. The Difference Between Mono, Stereo, and Multi
- 2.2. How to Control Control Signals
- 2.3. Acoustic Echo Canceller (AEC)
- 2.4. Ambient Noise Compensator (ANC)
- 2.5. Audio Detector
- 2.6. Auto Gain Control (AGC)
- 2.7. Combiner: Room Combiner, Room Combiner plus Automixer
- 2.8. DCA
- 2.9. Delay
- 2.10. Dynamics: Compressor
- 2.11. Dynamics: Comp260
- 2.12. Dynamics: De-Esser
- 2.13. Dynamics: Ducker
- 2.14. Dynamics: Gate
- 2.15. Dynamics: Limiter
- 2.16. Dynamics: Paging Ducker
- 2.17. Dynamics: Program Ducker
- 2.18. Effect: Ping Pong Delay
- 2.19. Effect: REV-X
- 2.20. EQ: GEQ
- 2.21. EQ: PEQ
- 2.22. Fader
- 2.23. Feedback Suppressor: Notch FBS
- 2.24. Feedback Suppressor: Pitch Shift FBS
- 2.25. Filter: BPF
- 2.26. Filter: HPF
- 2.27. Filter: LPF
- 2.28. Input/Output: Dante In
- 2.29. Input/Output: USB In
- 2.30. Input/Output: Dante Out
- 2.31. Input/Output: USB Out
- 2.32. Input/Output: SD Card
- 2.33. Meter
- 2.34. Mixer: Delay Matrix, Matrix Mixer
- 2.35. Mixer: Dugan Automixer
- 2.36. Oscillator
- 2.37. Polarity
- 2.38. Probe
- 2.39. Router
- 2.40. Source Selector
- 2.41. Speaker Processor: Standard SPP
- 2.42. Speaker Processor: C-Series SPP (FIR)
- 3. Control Components
- 3.1. Control Methods for Control Components
- 3.2. Input (Normalized Value): Button
- 3.3. Input (Value): Button
- 3.4. Input (Normalized Value): Radio Button
- 3.5. Input (Value): Radio Button
- 3.6. Input (Normalized Value): Fader
- 3.7. Input (Value): Fader
- 3.8. Processing (Normalized Value): Logic
- 3.9. Processing (Normalized Value): NOT
- 3.10. Processing (Normalized Value): Flip-Flop
- 3.11. Processing (Normalized Value): Invert
- 3.12. Processing (Normalized Value): Compare
- 3.13. Processing (Normalized Value): Difference
- 3.14. Processing (Normalized Value): Max/Min
- 3.15. Processing (Value): Negate
- 3.16. Processing (Value): Compare
- 3.17. Processing (Value): Multi Compare
- 3.18. Processing (Value): Difference
- 3.19. Processing (Value): Max/Min
- 3.20. Processing: Delay
- 3.21. Processing: External Events
- 3.22. Processing: Suspend
- 3.23. Processing: Router
- 3.24. Controller: GPI In
- 3.25. Controller: GPI Out
- 3.26. Controller: Scheduler
- 3.27. Parameter Set
- 3.28. Snapshot
④ GEQ [ON] button
Switches the GEQ function between enabled and disabled.
⑤ Bypass buttons
Specify whether each band is bypassed. If you click a button to make it light, that band is bypassed.
⑥ Gain faders
Adjust the output gain of each band.
⑦ [±15]/[±12]/[±6]/[‒24] buttons
Select the range of GEQ gain adjustment. When you click a button, the display of the gain faders and
EQ curve will change to the range you select.
⑧ [FLAT] button
Moves all gain faders to the 0 position.
⑨ [HPF] knob/HPF[BYPASS] button
Specifies the cutoff frequency of the high-pass filter. If you are not using the high-pass filter, click
the [BYPASS] button to turn bypass on (lit).
⑩ [LPF] knob/LPF[BYPASS] button
Specifies the cutoff frequency of the low-pass filter. If you are not using the low-pass filter, click
the [BYPASS] button to turn bypass on (lit).
⑪ [B/W-Q] list/knob
Specifies the width of the frequency band adjusted by the notch filter in the list box, and set the
width with the knob.
⑫ [Freq.] knob
Specifies the center frequency of the notch filter.
⑬ NOTCH [BYPASS] button
Switches the notch filter bypass on/off. If you are not using the notch filter, turn bypass on (lit).
2.20.2. Control
There are no parameters that can be controlled through the Control layer.
2. Audio Components
ProVisionaire Design Component Guide | 63