User Manual
Table Of Contents
- Как пользоваться данным справочным руководством
- Содержание
- Иерархия функций
- Секция SELECTED CHANNEL
- Секция Centralogic
- Подключение на входе и выходе
- Входные каналы
- Прохождение сигналов для входных каналов
- Определение названия и значка канала
- Выполнение настроек HA (предусилитель)
- Передача сигнала из входного канала на шины STEREO/MONO
- Передача сигнала из входного канала на шину MIX/MATRIX
- Корректировка задержки между каналами (Input Delay (задержка на входе))
- Операции с библиотеками каналов
- Выходные каналы
- Эквалайзер и динамический процессор
- Группирование и связывание
- Банки памяти сцен
- О банках памяти сцен
- Использование банков памяти сцен
- Редактирование банков памяти сцен
- Применение функции Global Paste (глобальная вставка)
- Использование функции Focus (фокусировка)
- Использование функции Recall Safe (безопасное восстановление)
- Использование функции Fade (изменение громкости звука)
- Вывод сигнала управления на внешнее устройство вместе с загрузкой сцены (GPI OUT)
- Воспроизведение аудиофайла, связанного с загрузкой сцены
- Функции Monitor (монитор) и Cue (контроль)
- Двусторонняя связь и осциллятор
- Индикаторы
- Графический эквалайзер, эффекты и Premium Rack
- Стойка ввода-вывода и внешний предусилитель
- MIDI
- Функциональные возможности MIDI на консоли серии CL
- Основные настройки MIDI
- Применение сообщений Program Change (изменение программы) для восстановления объектов сцен и библиотек
- Использование сообщений Control Change (изменение управления) для управления параметрами
- Использование сообщений Parameter Change для управления параметрами
- Пользовательские настройки (Безопасность)
- Настройки пользовательского уровня
- Предпочтения
- Клавиши USER DEFINED (определяемые пользователем)
- Определяемые пользователем регуляторы
- Доступные для переназначения преобразователи
- Пользовательский банк фейдеров
- Мастер-фейдер
- Блокировка консоли
- Сохранение и загрузка данных настройки с/на флэш- память USB
- Загрузка файла с флэш-памяти USB
- Форматирование флэш-памяти USB
- Устройство записи
- Прочие функции
- Об экране SETUP (настройка)
- Настройки синхронизации слов и гнезд
- Использование каскадных подключений
- Основные параметры для шин MIX и MATRIX
- Настройка яркости сенсорного экрана, светодиодных индикаторов, экранов с названиями каналов и ламп
- Установка даты и времени встроенных часов
- Установка сетевого адреса
- Инициализация модуля с восстановлением заводских настроек по умолчанию
- Корректировка точки срабатывания сенсорного экрана (функция калибровки)
- Корректировка фейдеров (функция калибровки)
- Точная настройка усиления входного и выходного сигналов (функция калибровки)
- Регулировка цвета канала (функция калибровки)
- Настройки аудиосети Dante
- Использование GPI (General Purpose Interface — интерфейс общего назначения)
- Т аблица характеристик MIDI-интерфейса
- Приложения
- Список элементов библиотеки EQ
- Список элементов библиотеки DYNAMICS
- Параметры Dynamics (динамический процессор)
- Список типов эффектов
- Параметры эффектов
- Параметры процессора Premium Rack
- Синхронизация эффектов с темпом
- Параметры, которые можно назначить для смены контроллеров
- Назначение параметров NRPN (незарегистрированный номер параметра)
- Применимость параметров микширования
- Функции, которые можно назначить клавишам USER DEFINED
- Функции, которые можно назначить для регуляторов USER DEFINED
- Функции, которые можно назначить для доступных для переназначения преобразователей
- Формат MIDI-данных
- Сообщения об ошибках/предупреждения
- Электрические характеристики
- Основные параметры микшера
- Предметный указатель
Приложения
Справочное руководство
250
[Conversion from actual data to bulk data]
d[0-6]: actual data
b[0-7]: bulk data
b[0] = 0;
for( I=0; I<7; I++){
if( d[I]&0x80){
b[0] |= 1<<(6-I);
}
b[I+1] = d[I]&0x7F;
}
[Recovery from bulk data to actual data]
d[0-6]: actual data
b[0-7]: bulk data
for( I=0; I<7; I++){
b[0] <<= 1;
d[I] = b[I+1]+(0x80&b[0]);
}
3.3 PARAMETER CHANGE
Reception
This message is echoed if [PARAMETER CHANGE ECHO] is ON.
This message is received if [PARAMETER CHANGE Rx] is ON and [Rx CH] matches
the Device number included in the SUB STATUS. When a PARAMETER CHANGE is
received, the specified parameter will be controlled. When a PARAMETER REQUEST
is received, the current value of the specified parameter will be transmitted as a
PARAMETER CHANGE with its Device Number as the [Rx CH].
Transmission
If [PARAMETER CHANGE Tx] is ON, and you edit a parameter for which CONTROL
CHANGE transmission has not been enabled, a PARAMETER CHANGE will be
transmitted with the [Tx CH] as its device number.
In response to a PARAMETER REQUEST, a PARAMETER CHANGE will be
transmitted with [Rx CH] as its device number.
4 PARAMETER CHANGE details
4.1 CURRENT SCENE, SETUP, BACKUP, USER SETUP
4.1.1 Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] in [Tx CH] when [PARAMETER
CHANGE Tx] is on and the parameter is not registered on the [CONTROL CHANGE
EVENT LIST].
4.1.2 Format (PARAMETER REQUEST)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
via PARAMETER CHANGE immediately the data is received.
4.1.3 Data category
4.2 FUNCTION CALL – LIBRARY STORE, RECALL –
4.2.1 Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] (MIDI CH) in [Tx CH] when
[PARAMETER CHANGE Tx] is on.
4.2.2 Function Name
Command rx/tx Function
F0 43 1n 3E 19 … F7
RARAMETER CHANGE
rx/tx
CL series native parameter change
F0 43 3n 3E 19 … F7
PARAMETER REQUEST
rx/tx
CL series native parameter request
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
CL Series
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
0ddddddd dd
Data
::
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
CL Series
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
EOX 11110111 F7
End of exclusive
Data Category Name
0x01 00000001
Current Scene /Setup/Backup/
User Setup Data
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
????? CL
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 "L"
(ASCII CODE)
01101001 "i"
(ASCII CODE)
01100010 "b"
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Number High
0nnnnnnn nl
Number Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
EOX 11110111 F7
End of exclusive
Function Name
Store “LibStr__”
Recall “LibRcl__”
Unknown Factor Store “LibUnStr”
Unknown Factor Recall “LibUnRcl”
Store Undo (only Score) “LibStrUd”
Recall Undo (only Scene) “LibRclUd”