User Manual
Table Of Contents
- Como usar este Manual de Referência
- Sumário
- Árvore de funções
- Seção SELECTED CHANNEL (canal selecionado)
- Seção Centralogic
- Patch de entrada e saída
- Canais de entrada
- Fluxo do sinal para canais de entrada
- Especificando o nome/ícone do canal
- Configurações do HA (amplificador com cabeça)
- Enviando o sinal de um canal de entrada para o barramento STEREO/MONO
- Função de panorâmica adicionada (apenas canais de entrada mono)
- Enviando um sinal de um canal de entrada para um barramento MIX/MATRIX
- Indicação no visor do nome do canal
- Correção do atraso entre os canais (Input Delay)
- Saída surround para canais de entrada
- Operações da biblioteca de canais
- Canais OUTPUT
- EQ (equalizador) e dinâmica
- Trabalho de canal
- Memória de cena
- Armazenando e chamando cenas
- Edição de memórias de cena
- Uso da função Global Paste
- Usando a função Focus Recall
- Uso da função Fade
- Emitindo um sinal de controle para um dispositivo externo junto com a chamada de cena (GPI OUT)
- Reproduzindo um arquivo de áudio vinculado a uma chamada de cena
- Uso do modo de visualização
- Funções Monitor e Cue
- Talkback e Oscilador
- Medidores
- EQ gráfico, EQ paramétrico, efeitos e PREMIUM RACK
- Dispositivos de E/S e amplificadores com cabeça externos
- MIDI
- Gravador
- Configuração
- Sobre a tela SETUP (configuração)
- Configurações do usuário
- Preferências
- Teclas USER DEFINED
- Funções que podem ser atribuídas às teclas USER DEFINED
- Botões giratórios USER DEFINED
- Funções que podem ser atribuídas a botões giratórios USER DEFINED
- Codificadores atribuíveis
- Funções que podem ser atribuídas a codificadores atribuíveis
- Funções do botão giratório GAIN/PAN/ASSIGN (codificador atribuível)
- Banco de atenuadores personalizados
- Master Fader (atenuador mestre)
- Funções do banco de atenuadores personalizados
- Console Lock (bloqueio do console)
- Salvando e carregando dados de configuração de uma unidade flash USB
- Formatação de uma unidade flash USB
- Função de remontagem adicionada a unidades flash USB
- Configurações do Word Clock e dos compartimentos
- Usando conexões em cascata
- Configurações básicas dos barramentos MIX e MATRIX
- Como ligar/desligar toda a fonte de alimentação phantom
- Especificando o brilho da tela sensível ao toque, LEDs, visores de nome de canal e lâmpadas
- Definição da data e da hora do relógio interno
- Configuração do endereço de rede
- Configurações da rede de áudio Dante
- Uso da GPI (General Purpose Interface)
- Função Help (ajuda)
- Outras funções
- Inicializando a unidade com as configurações padrão de fábrica
- Ajustando o ponto de detecção da tela sensível ao toque (função Calibration (calibração))
- Ajustando os atenuadores (função Calibration)
- Fazendo ajustes finos no ganho de entrada e saída (função Calibration)
- Ajustando a cor do canal (função Calibration)
- Como ajustar o brilho do visor de nome do canal
- Como ajustar o contraste do visor de nome do canal
- Inicializando as configurações do console e da rede de áudio Dante
- Procedimento de atualização alterado para o firmware NAME SUB CPU
- Função de atualização adicionada ao firmware Dante
- Mensagens de advertência/erro
- Índice remissivo
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Data List
45
Electrical Characteristics
All faders are nominal when measured. Output impedance of signal generator:150ohms
Frequency Response. Fs= 44.1 kHz or 48 kHz @20 Hz-20 kHz, referenced to
the nominal output level @1 kHz
Total Harmonic Distortion. Fs= 44.1 kHz or 48 kHz
* Total Harmonic Distortion is measured with a 18 dB/octave filter @80 kHz
Hum & Noise. Fs= 44.1 kHz or 48 kHz, EIN= Equivalent Input Noise
* Hum & Noise are measured with A-weight filter.
Dynamic Range. Fs= 44.1 kHz or 48 kHz
* Dynamic Range are measured with A-weight filter.
Sampling Frequency
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8
OMNI OUT 1-8 600 Ω
GAIN: +66dB
-1.5 0.0 0.5
dB
PHONES 8 Ω -3.0 0.0 0.5
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω
+4 dBu @20 Hz-20 kHz, GAIN: +66dB 0.1
%
+4 dBu @20 Hz-20 kHz, GAIN: -6dB 0.05
Internal OSC
OMNI OUT 1-8 600 Ω Full Scale Output @1 kHz 0.02
PHONES 8 Ω
Full Scale Output @1 kHz, PHONES Level
Control: Max.
0.2
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω
Rs= 150 Ω, GAIN: +66dB
Master fader at nominal level and one
Ch fader at nominal level.
-128
EIN
dBu
-62
Rs= 150 Ω, GAIN: -6dB
Master fader at nominal level and one
Ch fader at nominal level.
-84 -79
All INPUTs OMNI OUT 1-8 600 Ω
Rs= 150 Ω, GAIN: -6dB
Master fader at nominal level and all
OMNI IN 1-8 in faders at nominal level.
-70
- OMNI OUT 1-8 600 Ω Residual Output Noise, ST Master Off -88
-PHONES 8 Ω
Residual Output Noise, PHONES Level
Control Min.
-88
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω AD + DA, GAIN: -6dB 108 dB
- OMNI OUT 1-8 600 Ω DA Converter 112 dB
Parameter Conditions Min. Typ. Max. Unit
External Clock
Frequency
Range
Fs= 44.1 kHz
Fs= 45.9375 kHz (44.1 kHz +4.1667%)
Fs= 44.1441 kHz (44.1 kHz +0.1%)
Fs= 44.0559 kHz (44.1 kHz -0.1%)
Fs= 42.336 kHz (44.1 kHz -4.0%)
-200 +200 ppm
Fs= 48 kHz
Fs= 50 kHz (48 kHz +4.1667%)
Fs= 48.048 kHz (48 kHz +0.1%)
Fs= 47.952 kHz (48 kHz -0.1%)
Fs= 46.080 kHz (48 kHz -4.0%)
Jitter of PLL
DIGITAL IN Fs= 44.1 kHz
DIGITAL IN Fs= 48 kHz
10 ns
Internal Clock
Frequency
Word Clock : Int 44.1 kHz 44.1
kHz
Word Clock : Int 48 kHz 48
Accuracy
Word Clock : Int 44.1 kHz
-50 +50 ppm
Word Clock : Int 48 kHz
Jitter
Word Clock : Int 44.1 kHz 4.429
ns
Word Clock : Int 48 kHz 4.069