User Manual
Table Of Contents
- Utilisation du présent manuel de référence
- Table des matières
- Structure des fonctions
- Section SELECTED CHANNEL
- Section Centralogic
- Assignation des entrées et des sorties
- Canaux d'entrée
- Flux du signal des canaux d'entrée
- Spécification du nom et de l'icône du canal
- Réglages HA (préampli micro)
- Envoi d'un signal depuis un canal d'entrée vers le bus STEREO/MONO
- Ajout d'une fonction de panoramique (Canaux d'entrée mono seulement)
- Envoi d'un signal depuis un canal d'entrée vers un bus MIX/MATRIX
- Indication d'affichage des noms de canaux
- Correction du retard des signaux entre les canaux (Input Delay)
- Sortie surround pour les canaux d'entrée
- Opérations liées à la bibliothèque de canaux
- Canaux de sortie
- Le flux des signaux liés aux canaux de sortie
- Spécification du nom et de l'icône de canal
- Envoi de signaux depuis les canaux MIX vers le bus STEREO/MONO
- Envoi de signaux depuis les canaux MIX et STEREO/MONO vers les bus MATRIX
- Correction du retard des signaux entre les canaux (Output Delay)
- Opérations liées à la bibliothèque de canaux
- Égaliseur et dynamiques
- Tâche de canal
- Mémoire de scènes
- Stockage et rappel de scène
- Édition des mémoires de scènes
- Utilisation de la fonction Global Paste
- Utilisation de la fonction Focus Recall
- Utilisation de la fonction Fade
- Émission en sortie d'un signal de contrôle vers un périphérique externe en tandem avec un rappel de scène (GPI OUT)
- Reproduction d'un fichier audio lié à un rappel de scène
- Utilisation du mode Preview
- Fonctions Monitor et Cue
- Fonctions Talkback et Oscillator
- Indicateurs de niveau
- Égaliseur graphique, égaliseur paramétrique, effets et Premium Rack
- À propos du rack virtuel
- Opérations liées au rack virtuel
- Opérations liées à l'EQ graphique
- À propos d'AUTOMIXER
- Édition des paramètres des effets internes
- Synchronisation des effets et du tempo
- Utilisation de Premium Rack
- Utilisation des bibliothèques de l'EQ graphique, de l'EG paramétrique, des effets et de Premium Rack
- Périphériques d'E/S et préamplis micro externes
- MIDI
- Fonctionnalité MIDI de la console de série CL
- Réglages MIDI de base
- Utilisation de changements de programme pour rappeler des scènes et des éléments de la bibliothèque
- Utilisation de changements de commande pour contrôler des paramètres
- Commande des paramètres via les messages de changements de paramètre
- Enregistreur
- À propos de l'enregistreur sur mémoire USB
- Affectation des canaux aux entrée/ sortie de l'enregistreur
- Enregistrement de données audio sur un lecteur flash USB
- Reproduction de fichiers audio depuis un lecteur flash USB
- Édition de la liste de titres
- Enregistrement ou reproduction sur ordinateur à l’aide d’un logiciel DAW
- Utilisation de la console CL avec Nuendo Live
- Configuration
- À propos de l'écran SETUP
- Réglages utilisateur
- Préférences
- Touches USER DEFINED
- Fonctions pouvant être affectées aux touches USER DEFINED
- Boutons USER DEFINED
- Fonctions pouvant être affectées à des boutons USER DEFINED
- Encodeurs attribuables
- Fonctions pouvant être affectées à des encodeurs attribuables
- Fonctions affectées aux boutons GAIN/PAN/ASSIGN (encodeurs attribuables)
- Custom Fader Bank (Banque de faders personnalisés)
- Fader principal
- Fonctions liées aux banques de faders personnalisés
- Console Lock
- Sauvegarde et chargement des données de configuration vers et depuis un lecteur flash USB
- Formatage d'un lecteur flash USB
- Ajout d'une fonction de remontage du lecteur flash USB.
- Réglages de l'horloge de mot et des logements
- Utilisation des connexions en cascade
- Réglages de base des bus MIX et MATRIX
- Activation/désactivation de l'alimentation fantôme principale dans son ensemble
- Réglage de la luminosité de l'écran tactile, des voyants DEL, de l'affichage des noms de canaux et des témoins lumineux
- Réglage de la date et l'heure de l'horloge interne
- Réglage de l'adresse réseau
- Réglages du réseau audio Dante
- Dante Device Lock
- Prise en charge de Dante Domain Manager
- Utilisation de GPI (Interface à usage général)
- Fonction de l'aide
- Autres fonctions
- Réinitialisation de l'unité sur les réglages d'usine par défaut
- Réglage du point de détection de l'écran tactile (fonction Calibration)
- Réglage des faders (fonction Calibration)
- Réglage précis du gain d'entrée et de sortie (fonction Calibration)
- Réglage de la couleur de canal (fonction Calibration)
- Règlage de la luminosité de l'afficheur du nom de canal
- Réglage du contraste de l'afficheur du nom de canal
- Réinitialisation des réglages de la console et des réglages du réseau audio Dante
- Modification de la procédure de mise à jour du microprogramme NAME SUB CPU
- Ajout d'une fonction de mise à jour du microprogramme Dante
- Message d'avertissement et d'erreur
- Index
- Data List
Data List
19
EQUALIZER601
This effect emulates the characteristics of 70's analog equalizers. Re-creating the distortion
of typical analog circuits will add drive to the sound.
OPENDECK
It emulates the tape compression created by two open reel tape recorders (a recording deck
and a playback deck). You can change the sound quality by adjusting various elements, such
as the deck type, tape quality, playback speed, etc.
M.BAND DYNA.
Two input, two output 3-band dynamically controlled processor, with individual solo and gain
reduction metering for each band.
Parameter Range Description
LO TYPE HPF-2/1, LSH-1/2 Type of EQ1
LO F 16.0 Hz to 20.0 kHz Cut-off frequency of EQ1
LO G -18.0 to +18.0 dB Gain of EQ1
MID1 Q 0.50-16.0 Q of EQ2
MID1 F 16.0 Hz to 20.0 kHz Center frequency of EQ2
MID1 G -18.0 to +18.0 dB Gain of EQ2
MID2 Q 0.50-16.0 Q of EQ3
MID2 F 16.0 Hz to 20.0 kHz Center frequency of EQ3
MID2 G -18.0 to +18.0 dB Gain of EQ3
INPUT -18.0 to +18.0 dB Input gain
OUTPUT -18.0 to +18.0 dB Output gain
MID3 Q 0.50-16.0 Q of EQ4
MID3 F 16.0 Hz to 20.0 kHz Center frequency of EQ4
MID3 G -18.0 to +18.0 dB Gain of EQ4
MID4 Q 0.50-16.0 Q of EQ5
MID4 F 16.0 Hz to 20.0 kHz Center frequency of EQ5
MID4 G -18.0 to +18.0 dB Gain of EQ5
HI TYPE LPF-2/1, HSH-1/2 Type of EQ6
HI F
16.0 Hz to 20.0 kHz
*1
*1. 16.0 Hz to 20.0 kHz (LPF-1, LPF-2), 1.0 kHz to 20.0 kHz (HSH-1, HSH-2)
Cut-off frequency of EQ6
HI G -18.0 to +18.0 dB Gain of EQ6
LO SW OFF, ON Switches EQ1 on/off
MID1 SW OFF, ON Switches EQ2 on/off
MID2 SW OFF, ON Switches EQ3 on/off
MID3 SW OFF, ON Switches EQ4 on/off
MID4 SW OFF, ON Switches EQ5 on/off
HI SW OFF, ON Switches EQ6 on/off
TYPE CLEAN, DRIVE
Selects the equalizer type.
The CLEAN equalizer provides non-distorted, clear, typical digital sound,
emulating variations in frequency response in the analog circuits. The
DRIVE equalizer provides distorted, driven sound that enhances analog
flavor, emulating changes in frequency response in the analog circuits.
Parameter Range Description
REC DEC
Swss70, Swss78, Swss85,
Amer70
Selects the recording deck type
REC LVL -96.0 to +18.0 dB
Adjusts the input level of the recording deck. As you raise the level, tape
compression is generated, which narrows the dynamic range and distorts
the sound.
REC HI -6.0 to +6.0 dB Adjusts the high range gain of the recording deck
REC BIAS -1.00 to +1.00 Adjusts the bias of the recording deck
REPR DEC
Swss70, Swss78, Swss85,
Amer70
Selects the playback deck type
REPR LVL -96.0 to +18.0 dB Adjusts the output level of the playback deck
REPR HI -6.0 to +6.0 dB Adjusts the high range gain of the playback deck
REPR LO -6.0 to +6.0 dB Adjusts the low range gain of the playback deck
MAKE UP Off, On
When you adjust the REC LVL, the REPR LVL reflects the change,
maintaining the relative output level. You can change the amount of
distortion without changing the output level.
TP SPEED 15ips, 30ips Selects the tape speed
TP KIND Old, New Selects the tape type
Parameter Range Description
L-M XOVER 21.2 Hz-8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz-8.00 kHz Crossover frequency between the mid and high bands
SLOPE -6 dB, -12 dB Filter slope
LOW GAIN -12.0 dB to +12.0 dB Low band gain
MID GAIN -12.0 dB to +12.0 dB Mid band gain
HI. GAIN -12.0 dB to +12.0 dB High band gain
TOTAL -72.0 dB to +12.0 dB Overall gain
CEILING -6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
CMP.THRE -24.0 dB to 0.0 dB Threshold of the compressor
CMP.RAT 1:1 to 20:1 Ratio of the compressor
CMP.ATK 0-120 ms Attack time of the compressor
CMP.REL
*1
Release time of the compressor
CMP.KNEE 0-5 Knee of the compressor
CMP.BYP OFF/ON Bypasses the compressor
EXP.THRE -54.0 dB to -24.0 dB Threshold of the expander
EXP.RAT 1:1 to 5:1 Ratio of the expander
EXP.REL
*1
Release time of the expander
EXP.BYP OFF/ON Bypasses the expander
LIM.THRE -12.0 dB to 0.0 dB Threshold of the limiter