User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Monitor and Cue functions
V5 Reference Manual
122
Operating the Cue function
This section explains how to use the [CUE] key for a channel or DCA group to monitor cue
signals.
NOTE
The cue signal is sent to the same output destination as the monitor signal. Be aware that for this
reason, the cue signal will not be sent to the connected monitor speakers if you turn off the
Monitor function. However, the PHONES Out jack below the front pad will always output cue
signals regardless of the Monitor on/off setting. See “Using the Monitor function” (page 114) for
details about the Monitor function.
NOTE
• The cue signal is sent to the monitor output and PHONES Out jacks regardless of whether the
CUE OUTPUT button is on or off. However, the cue signal will no longer be sent to monitor output
if CUE INTERRUPTION is turned off. The cue signal is always sent to the PHONES Out jack,
regardless of the CUE INTERRUPTION setting.
• When using the MIX/MATRIX bus select buttons in the SENDS ON FADER window, you can
press the selected button once again to turn on Cue for the corresponding MIX/MATRIX channel
(page 46).
• If you want cue operations and channel select operations to be linked, open the USER SETUP
window, choose the PREFERENCE tab, and then turn on [CUE] [SEL] LINK (page 223).
• You can also assign the function of the CLEAR CUE button to a USER DEFINED key (page 224).
• If PHONES LEVEL LINK (page 115) in the MONITOR screen is ON, the cue signal level when
monitoring through headphones can be adjusted using both the MONITOR LEVEL knob and the
PHONES LEVEL knob.
• To adjust the level to the output destination port for the cue signal, adjust the gain of the output
port that is patched to it.
• If you turn on the [CUE] key or the CUE button on the display, the CUE meter is displayed in the
Function Access Area, indicating the CUE output level. The upper part of the cue meter shows
an abbreviation indicating the currently-on cue group or cue button. The abbreviations displayed
for the cue meters have the following meaning.
STEP
1. In the Function Access Area, press the MONITOR button.
2. Press the CUE display button or the INPUT/DCA/OUTPUT CUE field in the MONITOR
screen.
3. Use the CUE MODE button in the CUE screen to specify what will happen when
multiple [CUE] keys within the same CUE group are turned on.
4. Use the buttons and knobs of the INPUT CUE/DCA CUE/OUTPUT CUE field to specify
the output position and output level for each CUE group.
5. Press one of the CUE OUT PATCH buttons (L/R) in the meter field to specify a port
as the output destination for cue signals L and R (multiple selections are allowed).
6. Press the [CUE] key of the channel or DCA group to be monitored to turn it on.
7. Adjust the Cue signal level by using the [MONITOR LEVEL] knob located in the
SCENE MEMORY/MONITOR section of the top panel.
8. To defeat cue, press the currently-on [CUE] key once again. To clear all cue
selections, press the CLEAR CUE button in the Meter field.
MONITOR screen
IN INPUT CUE group
DCA DCA CUE group
OUT OUTPUT CUE group
EFFECT
CUE button in the EFFECT and PREMIUM RACK windows
(Other CUE groups)
KEY IN
KEY IN CUE button in the DYNAMICS1 window
(Other CUE groups)
REC/PB
RECORDER INPUT CUE button or PLAYBACK OUT CUE button
(Other CUE groups)
CUE meter