User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
150
B PEQ IN/OUT level meters
Indicate the peak level of signals before and after the PEQ.
C Rack select tabs
Switch among GEQ 1-8, GEQ 9-16, or EFFECT 1-8. For a rack in which an 8BandPEQ is
mounted, the tabs will be split as xA and xB (x is the rack number).
NOTE
For details on how to use the buttons, refer to “Using the tool buttons” in the separate Owner’s
Manual.
D RTA button
Turn this button on to overlay a frequency response graph on the EQ.
E HOLD button
Press this button to hold the peak of the graph that displays RTA.
F EQ type select button
Switches the EQ type to PRECISE, AGGRESSIVE, SMOOTH, or LEGACY.
The following EQ types can be selected.
G Offset gain
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
PEQ EDIT window (8PEQ)
1 BYPASS button
You can bypass each band.
When the BYPASS button is on, the Q, FREQUENCY, and GAIN knobs for that band turn
gray.
2 HPF/LPF NOTCH button
Press this button to switch to the screen for operating HPF/LPF/notch filters.
3 EQ parameter setting knobs
Indicates the Q, FREQUENCY, and GAIN parameters for the BAND1 - BAND8 bands. You
can use a multifunction knob to adjust this.
PRECISE
This EQ type features “precision” and “controllability.” It can be used to
precisely adjust the desired points, to flexibly respond to a variety of music
production needs. The Low/High shelving filters have “Q” parameters that
allow knee adjustments.
AGGRESSIVE
This EQ type features “effective musical” characteristics. It allows you to
create an aggressive tone, making it a very powerful tool for artistic
expression.
SMOOTH
This EQ type focuses on a “smooth sound quality.” It allows you to create
natural sounds without significant modifications to the atmosphere of the
original sound.
LEGACY
This is the standard EQ type found in classic Yamaha digital mixers, such as
the PM1D and the PM5D. On the left side of the EQ graph, you can switch
between TYPE I (an algorithm used in previous Yamaha digital mixers) and
TYPE II (an algorithm that reduces interference between bands).
2
313
1