User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
236
GAIN/PAN/ASSIGN knob (assignable encoder)
functions
In CL V1.7 and later, the following functions have been added to SENDS ON FADER mode.
When using the [GAIN/PAN/ASSIGN] keys on the top panel to select
ASSIGN
Use assignable encoders to adjust the level of channels.
Channel name display indication
When using the [GAIN/PAN/ASSIGN] keys on the top panel to select
PAN
Use assignable encoders to adjust PAN sent from channels to the MIX/MATRIX bus (bus set
for Stereo send in the BUS SETUP screen).
Channel name display indication
Custom fader bank
Groups that organize channels routed to the top-panel faders are called “fader banks.”
There are input and output channel banks, as well as custom fader banks. Custom fader
banks enable you to select various combinations of channels, regardless of channel types.
This section explains how to set up a custom fader bank.
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the CUSTOM FADER BANK/MASTER FADER for Guest page, and make custom fader bank
settings for the Guest account.
• You can also press the fader assign select buttons to assign channels to faders.
Channel levels
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.
PAN sent from channel to MIX/MATRIX bus
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the CUSTOM FADER tab.
4. Use the Bank Select keys to recall the fader settings to the top panel for the channels
you want to add to the custom fader bank.
5. In the CUSTOM FADER BANK/MASTER FADER page, press the bank select button for
the custom fader bank you want to set up.
6. In the FADER field, press the select button for the fader you want to set up.
7. Press a [SEL] key on the top panel to assign a channel to the fader number selected
in step 6.
8. To assign channels to other faders, repeat steps 5 through 7.
USER SETUP window (CUSTOM
FADER BANK/MASTER FADER page)