User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
255
NETWORK window (FOR MIXER CONTROL page)
Use this window to set the console’s IP address, in order to use the NETWORK connector on
the rear panel to remote-control the console from CL Editor, StageMix, or the MonitorMix
application.
Set the UNIT Name and PIN for the MonitorMix application here.
For the IP SETTING MODE select buttons, only STATIC IP button is enabled. The other
buttons cannot be selected.
1 MAC ADDRESS
Indicates the MAC (Machine Access Control) address, which identifies a host in a
network. This address is for display only, and cannot be edited.
2 UNIT NAME
Sets the name to be shown on the network.
3 PIN for MonitorMix
Sets the PIN (4-digit numeric password) to be entered when using the MonitorMix
application to connect to a CL series console. MonitorMix is an iOS application that
musicians can use on stage to adjust their own monitor balance.
You can register a PIN with all 4 digits blank. In that case, PIN authentication with
MonitorMix is not required. However, you cannot leave only 1, 2, or 3 of the PIN digits
blank.
NOTE
The NETWORK connector on the CL series console transmits data via either 100BASE-TX
(transmission speed: maximum 100 Mbps) or 10BASE-T (transmission speed: max 10 Mbps).
NETWORK window (FOR DEVICE CONTROL page)
Use this window to set the console’s IP address, in order to use the Dante PRIMARY
connector on the rear panel to remote-control external devices. DHCP, AUTO IP, and fixed IP
settings are supported.
Even on DHCP networks, it is possible to remotely control external devices such as Tio1608-
D and Shure’s ULDX4.
1 CURRENT IP SETTING field
This field shows the current setting.
NOTE
If you use the IP SETTING MODE select buttons to select DHCP or AUTO IP, it may take some
time for the IP address to be configured. During this time, the window will appear as shown below.
3
1
2
6
1
7
2
3 4
5