User Manual
Table Of Contents
- Uso del presente Manuale di riferimento
- Sommario
- Schema delle funzioni
- Sezione SELECTED CHANNEL (CANALE SELEZIONATO)
- Sezione Centralogic
- Assegnazione ingressi e uscite
- Canali di input
- Flusso del segnale dei canali di ingresso
- Indicazione del nome e dell'icona del canale
- Impostazioni HA (preamplificatore)
- Invio del segnale da un canale di ingresso al bus STEREO/MONO
- Funzione pan aggiunta (solo canali di ingresso mono)
- Invio di un segnale da un canale di ingresso a un bus MIX/MATRIX
- Indicazione del display dei nomi dei canali
- Correzione del delay tra i canali (Delay di ingresso)
- Uscita surround per i canali di ingresso
- Operazioni nella libreria canali
- Canali di uscita
- EQ e dinamiche
- Channel Job (Operazione canale)
- Memoria scena
- Memorizzazione e richiamo di scene
- Modifica delle memorie scene
- Uso della funzione Global Paste (Incolla impostazioni globali)
- Uso della funzione Focus Recall
- Utilizzo della funzione Fade
- Uscita di un segnale di controllo a un dispositivo esterno collegato con richiamo della scena (GPI OUT)
- Riproduzione di un file audio collegato al richiamo di una scena
- Uso della modalità Preview
- Funzioni Monitor (Monitoraggio) e Cue (Segnale di attivazione)
- Talkback e oscillatore
- Indicatori
- EQ grafico, Equalizzatore parametrico, effetti e PREMIUM RACK
- Dispositivi I/O e preamplificatori esterni
- MIDI
- Registratore
- Informazioni sul registratore di memoria USB
- Assegnazione dei canali all'ingresso e all'uscita del registratore
- Registrazione dell'audio in un'unità di memoria flash USB
- Riproduzione di file audio da un'unità di memoria flash USB
- Modifica dell'elenco dei titoli
- Registrazione o riproduzione su un computer mediante DAW
- Uso della console CL con Nuendo Live
- Control AFC IMAGE
- Setup
- Informazioni sulla schermata SETUP
- Impostazioni utente
- Preferenze
- Tasti USER DEFINED
- Funzioni che possono essere assegnate a tasti USER DEFINED (definiti dall'utente)
- Manopole USER DEFINED
- Funzioni che possono essere assegnate a manopole USER DEFINED (definite dall'utente)
- Encoder assegnabili
- Funzioni che possono essere assegnate agli encoder assegnabili
- Funzioni della manopola GAIN/PAN/ASSIGN (encoder assegnabile)
- Banco di fader personalizzato
- Funzioni dei banchi di fader personalizzati
- Console Lock (Blocco console)
- Salvataggio e caricamento di dati di configurazione in e da un'unità di memoria flash USB
- Formattazione di un'unità di memoria flash USB
- Funzione per rimontare le unità flash USB aggiunta
- Impostazioni di wordclock e slot
- Uso dei collegamenti in cascata
- Impostazioni di base per i bus MIX e MATRIX
- Attivazione o disattivazione dell'intera alimentazione phantom
- Regolazione della luminosità dello schermo sensibile al tocco, dei LED, della visualizzazione dei nomi dei canali e delle spie
- Impostazione di data/ora del clock interno
- Impostazione dell'indirizzo di rete
- Impostazione della rete audio Dante
- Dante Device Lock
- Supporto per Dante Domain Manager
- Utilizzo di GPI (General Purpose Interface)
- Funzione Help (Guida)
- Altre funzioni
- Inizializzazione dell'unità alle impostazioni di fabbrica dell'unità
- Regolazione del punto di rilevamento dello schermo sensibile al tocco (funzione Calibration, Calibrazione)
- Regolazione dei fader (funzione Calibration)
- Regolazione fine del guadagno di input e uscita (funzione Calibration)
- Regolazione del colore dei canali (funzione di calibrazione)
- Regolazione della luminosità del display dei nomi dei canali
- Regolazione del contrasto dei display dei nomi dei canali
- Inizializzazione delle impostazioni della console e della rete audio Dante
- Procedura di aggiornamento modificata per il firmware NAME SUB CPU
- Funzione di aggiornamento del firmware Dante aggiunta
- Messaggi di avviso/errore
- Indice
- Data List
Data List
37
MIDI Data Format
This section explains the format of the data that the CL series
is able to understand, send, and receive.
1 CHANNEL MESSAGE
1.1 NOTE OFF (8n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.2 NOTE ON (9n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.3 CONTROL CHANGE (Bn)
Two types of CONTROL CHANGE can be transmitted and received; [NRPN]
(Non-Registered Parameter Numbers) and freely-assigned [TABLE] (1CH x 110)
messages. Select either [TABLE] or [NRPN].
Reception
These messages are echoed to MIDI OUT if [CONTROL CHANGE ECHO] is ON.
If [TABLE] is selected, these messages are received when [CONTROL CHANGE Rx]
is ON and [Rx CH] matches, and will control parameters according to the settings
of the [CONTROL CHANGE EVENT LIST]. For the parameters that can be
assigned, refer to “Parameters That Can Be Assigned to Control Changes”
(page 23).
If [NRPN] is selected, these messages are received when [CONTROL CHANGE Rx]
is ON and the [Rx CH] matches; the four messages NRPN control number (62h,
63h) and DATA ENTRY control number (06h, 26h) are used to control the
specified parameter.
Transmission
If [TABLE] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
parameter that is assigned in the [CONTROL CHANGE EVENT LIST], these
messages will be transmitted on the [Tx CH] channel. For the parameters that can
be assigned, refer to “Parameters That Can Be Assigned to Control Changes”
(page 23).
If [NRPN] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
specified parameter, the four messages NRPN control number (62h, 63h) and
DATA ENTRY control number (06h, 26h) are transmitted on the [Tx CH] channel.
For the parameters that can be assigned, refer to “Parameters That Can Be
Assigned to Control Changes” (page 23).
CONTROL CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
CONTROL CHANGE numbers 0 and 32 are for selecting banks.
If [TABLE] is selected
Equation for converting a Control Value to parameter data
paramSteps = paramMax-paramMin + 1;
add = paramWidth / paramSteps;
mod = paramWidth-add * paramSteps;
curValue = paramSteps * add + mod / 2;
(1) If the assigned parameter has fewer than 128 steps
paramWidth = 128; rxValue = Control value;
(2) If the assigned parameter has 128 or more but less than 16,384 steps
paramWidth = 16384;
(2-1) When High and Low data is received
rxValue = Control value(High) * 128 + Control value(Low);
(2-2) When only Low data is received
rxValue = (curValue & 16256) + Control value(Low);
(2-3) When only High data is received
rxValue = Control value(High) * 128 + (curValue & 127);
(3) If the assigned parameter has 16,384 or more but less than 2,097,152
steps
paramWidth = 2097152;
(3-1) When High, Middle, and Low data is received
rxValue = Control value(High) * 16384 + Control value(Middle) * 128 + Control value(Low);
(3-2) When only Low data is received
rxValue = (curValue & 2097024) + Control value(Low);
(3-3) When only Middle data is received
rxValue = (curValue & 2080895) + Control value(Middle) * 128;
(3-4) When only High data is received
rxValue = (curValue & 16383) + Control value(High) * 16384;
(3-5) When only Middle and Low data is received
rxValue = (curValue & 2080768) + Control value(Middle) * 128 + Control value(Low);
(3-6) When only High and Low data is received
rxValue = (curValue & 16256) + Control value(High) * 16384 + Control value(Low);
(3-7) When only High and Middle data is received
rxValue = (curValue & 127) + Control value(High) * 16384 + Control value(Middle) * 128;
if ( rxValue > paramWidth)
rxValue = paramWidth;
param = ( rxValue-mod / 2) / add;
If [NRPN] is selected
1.4 PROGRAM CHANGE (Cn)
Reception
If [PROGRAM CHANGE ECHO] is ON, bank select messages will also be echoed
from MIDI OUT.
If SINGLE CH is selected, these messages are received if [PROGRAM CHANGE Rx]
is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are
received regardless of the channel. When these messages are received, scene
memory, effect library and premium rack library are recalled according to the
settings of the [PROGRAM CHANGE EVENT LIST].
Transmission
If [PROGRAM CHANGE Tx] is ON, these messages are transmitted according to
the [PROGRAM CHANGE Table] settings when scene memory, effect library and
premium rack library are recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH] channel.
If the recalled scene memory, effect library and premium rack library have been
assigned to more than one PROGRAM NUMBER, the lowest-numbered
PROGRAM NUMBER for each MIDI channel will be transmitted.
PROGRAM CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
You can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
You can choose the Rx CH, OMNI CH, and Tx CH.
You can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The Rx and Tx channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select
messages will not be added.
You can make settings for up to sixteen MIDI channels.
STATUS 1000nnnn 8n
Note off message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (ignored)
STATUS 1001nnnn 9n
Note on message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (1-127:on, 0:off)
STATUS 1011nnnn Bn
Control change
DATA 00
Control number (00)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 20
Control number (32)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 0nnnnnnn nn
Control number (1-5, 7-31, 33-37, 38-95,
102-119) *
0vvvvvvv vv
Control Value (0-127)
* Numbers 0, 32, and 96-101 cannot be used.
* Control number 6, 38 can be used.
STATUS 1011nnnn Bn
Control change
DATA 01100010 62
NRPN LSB
0vvvvvvv vv
Parameter number LSB
STATUS 1011nnnn Bn
Control change *
DATA 01100011 63
NRPN MSB
0vvvvvvv vv
Parameter number MSB
STATUS 1011nnnn Bn
Control change *
DATA 00000110 06
Data entry MSB
0vvvvvvv vv
Parameter data MSB
STATUS 1011nnnn Bn
Control change *
DATA 00100110 26
Data entry LSB
0vvvvvvv vv
Parameter data LSB
* The STATUS byte of the second and subsequent messages need not
be added during transmission.
Reception must occur correctly whether or not the status byte is
omitted.
STATUS 1100nnnn Cn
Program change
DATA 0nnnnnnn nn
Program number (0-127)