User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5.8 Reference Manual
147
3 FADER ASSIGN field
In this field you can select the group of bands that will be controlled by the Centralogic
section’s faders. The buttons of the FADER ASSIGN field correspond to the following
groups of bands.
When you press one of these buttons, the faders for the bands selected on screen will
turn white, and the numbers of the corresponding faders in the Centralogic section will
be displayed. Now you can use the faders in the Centralogic section to control the
bands.
NOTE
The above operation is possible even if the Centralogic section is locked. When you turn off the
button in the FADER ASSIGN field, it will return to the locked state.
4 Tool buttons
Copy the currently-displayed 31BandGEQ settings to the GEQ of another rack, or
initialize the settings. For details on how to use the tool buttons, refer to “Using the tool
buttons” in the separate Owner’s Manual.
NOTE
• Only 31BandGEQ settings that use fifteen bands or less can be copied to a Flex15GEQ.
• GEQ settings can be stored and recalled at any time using the dedicated library.
Using the Flex15GEQ
You will use the Centralogic section’s faders 1-8 and [ON] keys to control the Flex15GEQ.
A rack in which a Flex15GEQ is mounted will show information for two GEQ units (A and B)
in the VIRTUAL RACK window.
NOTE
If you mount a Flex15GEQ, two monaural 31BandGEQ units will be placed in a single rack.
However, only up to fifteen bands can be adjusted for each unit.
NOTE
• The [ON] key will light if you raise or lower a fader even the slightest amount. This indicates that
the corresponding band is being modified.
• To quickly return a boosted or cut band to the flat position, press the corresponding [ON] key in
the Centralogic section to make it go dark.
• With CL version 2.0 or later, pressing the [ON] key again for this band will restore the adjusted
gain value. In this way, comparison is easy and quick. However, please note that if the [ON] key
for this band is off and if you press the [ON] key for the fader of a different frequency band, the
adjusted gain value will be canceled and will return to ± 0dB.
• If you switch the display to a different screen, the fader assignments in the Centralogic section
will forcibly be defeated. However if you once again display the same rack, the group of bands
you had previously been controlling will automatically be assigned to the faders.
• When you close the GEQ window, the buttons in the FADER ASSIGN field automatically turn off.
20-100 The eight bands 20.0 Hz--100 Hz
63-315 The eight bands 63.0 Hz--315 Hz
200-1k The eight bands 200 Hz--1.00 kHz
630-3.15k The eight bands 630 Hz--3.15 kHz
2k-10k The eight bands 2.00 kHz--10.0 kHz
4k-20k The eight bands 4.00 kHz--20.0 kHz
STEP
1. Press the rack container in which you mounted Flex15GEQ.
2. Press the GEQ ON/OFF button to turn the Flex15GEQ on.
3. Press one of the buttons in the FADER ASSIGN field to select the group of bands you
will control.
4. Use the faders in the Centralogic section to adjust the selected band.
5. When you’ve finished making settings, turn off the buttons in the FADER ASSIGN
field.