User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5.8 Reference Manual
253
WORD CLOCK/SLOT SETUP window
LEADER CLOCK SELECT field
1
Leader clock frequency display
Indicates the frequency (44.1 kHz or 48 kHz) of the currently-selected leader clock. If the
unit is not synching to the leader clock, “UNLOCK” will appear.
NOTE
• If sample rate pull-up/down has been specified in the Dante
Controller application, this area indicates the change in the
sample rate as a percentage, such as -4.0%, -0.1%, +0.1%, and
+4.1667%.
• To change the leader clock when sample rate pull-up/down has been specified, disable the pull-
up/down in the Dante Controller, change the leader clock, then specify pull-up/down again.
2 Leader clock select buttons
Use the buttons to select the clock source that you want to use as the word clock leader
from the following options:
• INT 48 k
• INT 44.1 k
The CL console internal clock (sampling rate 48 kHz or 44.1 kHz) will be the clock
source.
• WORD CLOCK IN
The word clock supplied from the WORD CLOCK IN jack on the rear panel of the console
will be used as the clock source.
• DANTE 48 k
• DANTE 44.1 k
The word clock supplied from the Dante jack on the rear panel of the console will be
used as the clock source.
NOTE
With CL V2.03 and later, if you initialize the console to factory settings, the default value for the
word clock is set to DANTE 48k. This allows you to synchronize word clock even when using
multiple CL and QL consoles at their default settings.
•SLOT 1-3
The word clock supplied via a digital I/O card installed in a console slot will be used as
the clock source. Word clock can be selected in pairs for each slot.
3 Clock status Indicator
Indicates the console’s status as a leader or a follower in the Dante audio network.
NOTE
When is displayed and the specified word clock is not synchronized
with a device acting as a Dante leader, the audio might cut out.
4 Clock status display
Indicates the status of synchronization with the leader clock for each clock source. Each
indicator is explained below:
• LOCKED (light blue)
Indicates that a clock synchronized with the selected clock source is being input. If an
external device is connected to the corresponding connector or slot, input/output is
occurring properly between that device and the CL series console. If the sampling
frequency is close, this status may be displayed even if not synchronized.
• LOCKED, BUT NOT SYNC’ED (yellow)
A valid clock is being input, but is not synchronized with the selected clock source. If an
external device is connected to the corresponding connector, input/output cannot
occur correctly between that device and the CL series console.
• SRC ON (green)
This is a special status that applies only to SLOT1-3. It indicates that SCR (Sample Rate
Converter) is enabled for the corresponding channel. This means that even if the signal
is not synchronized, normal input/output with the CL series console is occurring.
• UNLOCKED (red)
A valid clock is not being input. If an external device is connected to the corresponding
connector, input/output cannot occur correctly between that device and the CL series
console.
3
1
5
2
4
7
6
8
Leader
Follower