User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
146
8 HOLD button
Press this button to hold the peak of the graph that displays RTA.
9 Offset gain
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
Using the 31BandGEQ
You will use the Centralogic section’s faders 1-8 and [ON] keys to control the 31BandGEQ.
NOTE
• When a fader of the Centralogic section is in the center (flat) position, the corresponding [ON] key
will go dark. This indicates that the corresponding band is not being modified. If you raise or lower
the fader even the slightest amount, the [ON] key will light, indicating that this band has been
modified. If you press a lit [ON] key to make it go dark, the corresponding band will immediately
return to the flat state.
• With CL version 2.0 or later, pressing the [ON] key again for this band will restore the adjusted
gain value. In this way, comparison is easy and quick. However, please note that if the [ON] key
for this band is off and if you press the [ON] key for the fader of a different frequency band, the
adjusted gain value will be canceled and will return to ± 0dB.
• If you switch the display to a different screen or rack, the fader assignments in the Centralogic
section will forcibly be defeated. However if you once again display the same rack, the faders will
automatically move to the group of bands you had previously been controlling.
• When you close the GEQ EDIT window, the buttons in the FADER ASSIGN field automatically
turn off.
GEQ EDIT window (31BandGEQ)
1 EQ graph
Indicates the approximate response of the current 31Band GEQ.
2 Faders
Indicate the amount of boost and cut for each band of the 31BandGEQ. The actual
values are shown in the numerical boxes below.
Faders can be controlled by the TOUCH AND TURN function. The area of a fader you
touched will turn pink as shown below.
STEP
1. In the GEQ field rack, press the rack container in which you mounted the
31BandGEQ.
2. Press the GEQ ON/OFF button to turn the 31BandGEQ on.
3. Press one of the buttons in the FADER ASSIGN field to select the group of bands you
will control.
4. Use the faders in the Centralogic section to adjust the selected band.
5. When you’ve finished making settings, turn off the buttons in the FADER ASSIGN
field.
1
2
3
4