User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
I/O devices and external head amps
V5 Reference Manual
190
VIRTUAL RACK screen (EXTERNAL HA page)
1 EXTERNAL HA field
This displays the state of the connected external HA.
2 ID/Model name/+48V master
This displays information for the external HA mounted in the rack. The ID number is
automatically assigned in order of the connected devices from 1 to 6. This field also
enables you to view the on/off status of the master phantom power.
3 Virtual racks
These are up to six racks in which remotely controllable external HA units can be
mounted. If an external HA is mounted, this field will indicate the HA settings (GAIN
setting, and on/off status of the phantom power and HPF). Press a rack to open the
EXTERNAL HA window for that rack.
4 EXTERNAL HA PORT SELECT button
Press this button to display the HA PORT SELECT window, in which you can set the input
port for the external head amp mounted in the rack.
NOTE
If an external HA is connected to one of the slots on the CL series console, you must specify an
appropriate input port manually. If this is set incorrectly, the external HA will not be detected
correctly when you patch input ports to input channels.
5 VIEW switch buttons
Switch the virtual rack display between SB168-ES and AD8HR. Select the view that’s
appropriate for the connected device.
6 COMM PORT switch buttons
Specify whether the external HA connected to the slot will be controlled remotely. Select
“SLOT1” if you want to remotely control the external HA.
EXTERNAL HA PORT SELECT window
Select the input port for the external head amp. Display this window by pressing the
EXTERNAL HA PORT SELECT button in the I/O DEVICE screen (EXTERNAL HA page).
1 PORT SELECT buttons
Specify the input ports to which the external HA is connected.
2 3 4
1
5 6
1