User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
MIDI
V5 Reference Manual
195
Using program changes to recall scenes and library
items
The CL series console lets you assign a specific event (scene recall or effect library recall) to
each Program Change number, so that when this event is executed on the CL console, a
Program Change message of the corresponding number will be transmitted to an external
device. Conversely, the corresponding event can be executed when a Program Change
message is received from an external device.
NOTE
Assignments to program numbers are maintained as settings for the entire system, rather than
for individual scenes.
MIDI/GPI screen (PROGRAM CHANGE page)
In the PROGRAM CHANGE page, you can specify how Program Changes will be transmitted
and received, and choose the event (scene recall or effect library recall) that will be assigned
to each program number.
1 PROGRAM CHANGE field
Switches Program Change transmission and reception on or off. This setting is linked
with the PROGRAM CHANGE section of the MIDI SETUP page.
• Tx..................If this is on, the corresponding Program Change messages will be
transmitted when events on the list are executed.
• Rx .................If this is on, the corresponding events will be executed when Program
Change messages are received.
• ECHO............If this button is on, Program Change messages received from an
external device will be retransmitted without change.
2 PROGRAM CHANGE MODE field
Enables you to select the Program Change transmit/receive mode. This setting is linked
with the PROGRAM CHANGE MODE section of the MIDI SETUP page.
• Multi mode (when the MULTI button is on):
Program changes of all MIDI channels will be transmitted and received. (The transmit/
receive channel specified in the MIDI SETUP page will be ignored.) When a Program
Change is received, the event assigned to the corresponding MIDI channel and program
number in the list will be executed.
When you execute a specific event on a CL series console, the Program Change of the
corresponding program number will be transmitted on the MIDI channel shown in the
list. (If an event is assigned to more than one program number on multiple MIDI
channels/multiple program numbers, only the lowest-numbered program number on
each MIDI channel will be transmitted.)
STEP
1. Connect the CL series console to an external device.
2. As described in “Basic MIDI settings” (page 192), select the ports and MIDI channels
that will be used to transmit/receive program changes.
3. Press the PROGRAM CHANGE tab in the MIDI/GPI screen.
4. In the PROGRAM CHANGE page, switch Program Change transmission/reception on
or off, select transmission/reception mode, and set echo output.
5. To change the event assignment for each program number, press the desired event
in the list and select an event type and the recall target.
MIDI/GPI screen
(PROGRAM CHANGE page)
1
4
5
6
2
3