User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Recorder
V5 Reference Manual
209
Using the CL console with Nuendo Live
The CL series consoles can operate in an integrated manner with Steinberg’s Nuendo Live
DAW software.
The “Yamaha Console Extension” software which integrates the CL series and Nuendo Live
can be installed in your computer, allowing you to operate Nuendo Live from the CL series
console to easily perform multi-track recording operations.
Here we explain how to operate Nuendo Live from the CL series console.
Preparing the project
Refer to “Recording or playing back using a computer DAW” (page 206) to make the following
settings.
• Setting up Dante Virtual Soundcard
• Setting up Dante Controller
• Setting up Nuendo Live
Recording into a project
RECORDER screen (when selecting the Nuendo Live tab)
1 Nuendo meter display field
This shows the channel levels of Nuendo Live.
2 PEAK CLEAR button
Clears the peak levels indicated by the peak hold function.
3 Marker list field
Lists the marker information recorded in the current Nuendo Live project.
The markers can be selected by pressing the on-screen list or by using the multifunction
knobs.
When you press this field, a keyboard window allowing you to edit the marker
information will appear.
4 Nuendo Live SETUP button
Specify the device that the console will use for communication when working with
Nuendo Live (page 210).
5 DANTE INPUT PATCH button
Press this to access the DANTE INPUT PATCH window (page 174).
6 Location information display
This displays information for the current location of the Nuendo Live project. You can
press the button at the right to switch the time display format.
STEP
1. In the Function Access Area, press the RECORDER button.
2. Press the Nuendo Live tab in the upper right of the RECORDER screen.
3. Press the EASY RECORDING button to start recording.
4. When you finish recording, press the record lock button and then press the STOP
button.
RECORDER screen
(when selecting the Nuendo Live tab)
1
6
3
2
4
5
HEDCBA0987
I
F
G