User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
252
Basic settings for MIX buses and MATRIX buses
Follow the steps below to change the basic settings for MIX buses and MATRIX buses, such
as switching between stereo and monaural, and selecting the send point from which the
signal of an input channel will be sent. The settings you make in the following procedure are
saved as part of the scene.
BUS SETUP window
You can make various settings for MIX buses and MATRIX buses.
1 SIGNAL TYPE switch buttons
Select how signals are processed for every adjacent pair of buses. Select either STEREO
(stereo signal) or MONOx2 (monaural signal x 2).
2 Bus type/send point select buttons (MIX bus only)
For every adjacent pair of buses, you can select the bus type and (for vari-type) the send
point. These buttons correspond to the following parameters.
3 Send point select buttons (MATRIX bus only)
Select the pre-fader send point from the input channel. These buttons correspond to the
following parameters.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the BUS SETUP button.
3. Use the tabs in the BUS SETUP window to select the MIX bus or MATRIX bus.
4. Use the SIGNAL TYPE switch buttons to specify whether each bus will function as
STEREO (main parameters will be linked for two adjacent odd-numbered/even-
numbered buses) or MONOx2 (use as two monaural channels).
5. Use the bus type/send point select buttons to select the bus type and the position
from which the signal of the input channel will be sent.
6. As desired, turn the buttons in the PAN LINK field on or off.
SETUP screen BUS SETUP window
Button Bus type Pre-fader send point
VARI [PRE EQ] VARI Immediately before the EQ
VARI [PRE FADER] VARI Immediately before the fader
FIXED FIXED ---
Button Pre-fader send point
PRE EQ Immediately before the EQ
PRE FADER Immediately before the fader
1 42 1 43
55
MIX 1-16 page MIX BUS 17-24/MATRIX BUS page