User Manual
Table Of Contents
- Utilisation du présent manuel de référence
- Table des matières
- Structure des fonctions
- Section SELECTED CHANNEL
- Section Centralogic
- Assignation des entrées et des sorties
- Canaux d'entrée
- Flux du signal des canaux d'entrée
- Spécification du nom et de l'icône du canal
- Réglages HA (préampli micro)
- Envoi d'un signal depuis un canal d'entrée vers le bus STEREO/MONO
- Ajout d'une fonction de panoramique (Canaux d'entrée mono seulement)
- Envoi d'un signal depuis un canal d'entrée vers un bus MIX/MATRIX
- Indication d'affichage des noms de canaux
- Correction du retard des signaux entre les canaux (Input Delay)
- Sortie surround pour les canaux d'entrée
- Opérations liées à la bibliothèque de canaux
- Canaux de sortie
- Le flux des signaux liés aux canaux de sortie
- Spécification du nom et de l'icône de canal
- Envoi de signaux depuis les canaux MIX vers le bus STEREO/MONO
- Envoi de signaux depuis les canaux MIX et STEREO/MONO vers les bus MATRIX
- Correction du retard des signaux entre les canaux (Output Delay)
- Opérations liées à la bibliothèque de canaux
- Égaliseur et dynamiques
- Tâche de canal
- Mémoire de scènes
- Stockage et rappel de scène
- Édition des mémoires de scènes
- Utilisation de la fonction Global Paste
- Utilisation de la fonction Focus Recall
- Utilisation de la fonction Fade
- Émission en sortie d'un signal de contrôle vers un périphérique externe en tandem avec un rappel de scène (GPI OUT)
- Reproduction d'un fichier audio lié à un rappel de scène
- Utilisation du mode Preview
- Fonctions Monitor et Cue
- Fonctions Talkback et Oscillator
- Indicateurs de niveau
- Égaliseur graphique, égaliseur paramétrique, effets et Premium Rack
- À propos du rack virtuel
- Opérations liées au rack virtuel
- Opérations liées à l'EQ graphique
- À propos d'AUTOMIXER
- Édition des paramètres des effets internes
- Synchronisation des effets et du tempo
- Utilisation de Premium Rack
- Utilisation des bibliothèques de l'EQ graphique, de l'EG paramétrique, des effets et de Premium Rack
- Périphériques d'E/S et préamplis micro externes
- MIDI
- Fonctionnalité MIDI de la console de série CL
- Réglages MIDI de base
- Utilisation de changements de programme pour rappeler des scènes et des éléments de la bibliothèque
- Utilisation de changements de commande pour contrôler des paramètres
- Commande des paramètres via les messages de changements de paramètre
- Enregistreur
- À propos de l'enregistreur sur mémoire USB
- Affectation des canaux aux entrée/ sortie de l'enregistreur
- Enregistrement de données audio sur un lecteur flash USB
- Reproduction de fichiers audio depuis un lecteur flash USB
- Édition de la liste de titres
- Enregistrement ou reproduction sur ordinateur à l’aide d’un logiciel DAW
- Utilisation de la console CL avec Nuendo Live
- Configuration
- À propos de l'écran SETUP
- Réglages utilisateur
- Préférences
- Touches USER DEFINED
- Fonctions pouvant être affectées aux touches USER DEFINED
- Boutons USER DEFINED
- Fonctions pouvant être affectées à des boutons USER DEFINED
- Encodeurs attribuables
- Fonctions pouvant être affectées à des encodeurs attribuables
- Fonctions affectées aux boutons GAIN/PAN/ASSIGN (encodeurs attribuables)
- Custom Fader Bank (Banque de faders personnalisés)
- Fader principal
- Fonctions liées aux banques de faders personnalisés
- Console Lock
- Sauvegarde et chargement des données de configuration vers et depuis un lecteur flash USB
- Formatage d'un lecteur flash USB
- Ajout d'une fonction de remontage du lecteur flash USB.
- Réglages de l'horloge de mot et des logements
- Utilisation des connexions en cascade
- Réglages de base des bus MIX et MATRIX
- Activation/désactivation de l'alimentation fantôme principale dans son ensemble
- Réglage de la luminosité de l'écran tactile, des voyants DEL, de l'affichage des noms de canaux et des témoins lumineux
- Réglage de la date et l'heure de l'horloge interne
- Réglage de l'adresse réseau
- Réglages du réseau audio Dante
- Utilisation de GPI (Interface à usage général)
- Fonction de l'aide
- Autres fonctions
- Réinitialisation de l'unité sur les réglages d'usine par défaut
- Réglage du point de détection de l'écran tactile (fonction Calibration)
- Réglage des faders (fonction Calibration)
- Réglage précis du gain d'entrée et de sortie (fonction Calibration)
- Réglage de la couleur de canal (fonction Calibration)
- Règlage de la luminosité de l'afficheur du nom de canal
- Réglage du contraste de l'afficheur du nom de canal
- Réinitialisation des réglages de la console et des réglages du réseau audio Dante
- Modification de la procédure de mise à jour du microprogramme NAME SUB CPU
- Ajout d'une fonction de mise à jour du microprogramme Dante
- Message d'avertissement et d'erreur
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Data List
10
MOD. DELAY
One input, two output basic repeat delay with modulation.
DELAY LCR
One input, two output 3-tap delay (left, center, right).
ECHO
Two input, two output stereo delay with crossed feedback loop.
CHORUS
Two input, two output chorus effect.
Parameter Range Description
DELAY 0.0-2725.0 ms Delay time
FB. GAIN -99 to +99% Feedback gain
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
WAVE Sine/Tri Modulation waveform
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine DELAY
MOD.NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
DELAY L 0.0-2730.0 ms Left channel delay time
DELAY C 0.0-2730.0 ms Center channel delay time
DELAY R 0.0-2730.0 ms Right channel delay time
FB. DLY 0.0-2730.0 ms Feedback delay time
LEVEL L -100 to +100% Left channel delay level
LEVEL C -100 to +100% Center channel delay level
LEVEL R -100 to +100% Right channel delay level
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE C
*1
Used in conjunction with TEMPO to determine center channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Parameter Range Description
DELAY L 0.0-1350.0 ms Left channel delay time
DELAY R 0.0-1350.0 ms Right channel delay time
FB.DLY L 0.0-1350.0 ms Left channel feedback delay time
FB.DLY R 0.0-1350.0 ms Right channel feedback delay time
FB. G L -99 to +99%
Left channel feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
FB. G R -99 to +99%
Right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
LR FBG -99 to +99%
Left to right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
RL FBG -99 to +99%
Right to left channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FBL
*1
Used in conjunction with TEMPO to determine left channel feedback
DELAY
NOTE FBR
*1
Used in conjunction with TEMPO to determine right channel feedback
DELAY
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
AM DEPTH 0-100% Amplitude modulation depth
PM DEPTH 0-100% Pitch modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain