User Manual
Table Of Contents
- Utilisation du présent manuel de référence
- Table des matières
- Structure des fonctions
- Section SELECTED CHANNEL
- Section Centralogic
- Assignation des entrées et des sorties
- Canaux d'entrée
- Flux du signal des canaux d'entrée
- Spécification du nom et de l'icône du canal
- Réglages HA (préampli micro)
- Envoi d'un signal depuis un canal d'entrée vers le bus STEREO/MONO
- Ajout d'une fonction de panoramique (Canaux d'entrée mono seulement)
- Envoi d'un signal depuis un canal d'entrée vers un bus MIX/MATRIX
- Indication d'affichage des noms de canaux
- Correction du retard des signaux entre les canaux (Input Delay)
- Sortie surround pour les canaux d'entrée
- Opérations liées à la bibliothèque de canaux
- Canaux de sortie
- Le flux des signaux liés aux canaux de sortie
- Spécification du nom et de l'icône de canal
- Envoi de signaux depuis les canaux MIX vers le bus STEREO/MONO
- Envoi de signaux depuis les canaux MIX et STEREO/MONO vers les bus MATRIX
- Correction du retard des signaux entre les canaux (Output Delay)
- Opérations liées à la bibliothèque de canaux
- Égaliseur et dynamiques
- Tâche de canal
- Mémoire de scènes
- Stockage et rappel de scène
- Édition des mémoires de scènes
- Utilisation de la fonction Global Paste
- Utilisation de la fonction Focus Recall
- Utilisation de la fonction Fade
- Émission en sortie d'un signal de contrôle vers un périphérique externe en tandem avec un rappel de scène (GPI OUT)
- Reproduction d'un fichier audio lié à un rappel de scène
- Utilisation du mode Preview
- Fonctions Monitor et Cue
- Fonctions Talkback et Oscillator
- Indicateurs de niveau
- Égaliseur graphique, égaliseur paramétrique, effets et Premium Rack
- À propos du rack virtuel
- Opérations liées au rack virtuel
- Opérations liées à l'EQ graphique
- À propos d'AUTOMIXER
- Édition des paramètres des effets internes
- Synchronisation des effets et du tempo
- Utilisation de Premium Rack
- Utilisation des bibliothèques de l'EQ graphique, de l'EG paramétrique, des effets et de Premium Rack
- Périphériques d'E/S et préamplis micro externes
- MIDI
- Fonctionnalité MIDI de la console de série CL
- Réglages MIDI de base
- Utilisation de changements de programme pour rappeler des scènes et des éléments de la bibliothèque
- Utilisation de changements de commande pour contrôler des paramètres
- Commande des paramètres via les messages de changements de paramètre
- Enregistreur
- À propos de l'enregistreur sur mémoire USB
- Affectation des canaux aux entrée/ sortie de l'enregistreur
- Enregistrement de données audio sur un lecteur flash USB
- Reproduction de fichiers audio depuis un lecteur flash USB
- Édition de la liste de titres
- Enregistrement ou reproduction sur ordinateur à l’aide d’un logiciel DAW
- Utilisation de la console CL avec Nuendo Live
- Configuration
- À propos de l'écran SETUP
- Réglages utilisateur
- Préférences
- Touches USER DEFINED
- Fonctions pouvant être affectées aux touches USER DEFINED
- Boutons USER DEFINED
- Fonctions pouvant être affectées à des boutons USER DEFINED
- Encodeurs attribuables
- Fonctions pouvant être affectées à des encodeurs attribuables
- Fonctions affectées aux boutons GAIN/PAN/ASSIGN (encodeurs attribuables)
- Custom Fader Bank (Banque de faders personnalisés)
- Fader principal
- Fonctions liées aux banques de faders personnalisés
- Console Lock
- Sauvegarde et chargement des données de configuration vers et depuis un lecteur flash USB
- Formatage d'un lecteur flash USB
- Ajout d'une fonction de remontage du lecteur flash USB.
- Réglages de l'horloge de mot et des logements
- Utilisation des connexions en cascade
- Réglages de base des bus MIX et MATRIX
- Activation/désactivation de l'alimentation fantôme principale dans son ensemble
- Réglage de la luminosité de l'écran tactile, des voyants DEL, de l'affichage des noms de canaux et des témoins lumineux
- Réglage de la date et l'heure de l'horloge interne
- Réglage de l'adresse réseau
- Réglages du réseau audio Dante
- Utilisation de GPI (Interface à usage général)
- Fonction de l'aide
- Autres fonctions
- Réinitialisation de l'unité sur les réglages d'usine par défaut
- Réglage du point de détection de l'écran tactile (fonction Calibration)
- Réglage des faders (fonction Calibration)
- Réglage précis du gain d'entrée et de sortie (fonction Calibration)
- Réglage de la couleur de canal (fonction Calibration)
- Règlage de la luminosité de l'afficheur du nom de canal
- Réglage du contraste de l'afficheur du nom de canal
- Réinitialisation des réglages de la console et des réglages du réseau audio Dante
- Modification de la procédure de mise à jour du microprogramme NAME SUB CPU
- Ajout d'une fonction de mise à jour du microprogramme Dante
- Message d'avertissement et d'erreur
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Data List
20
M.BAND COMP
Two input, two output 3-band compressor, with individual solo and gain reduction metering for
each band.
Premium Rack Processor Parameters
Portico5033
This models an analog 5-band EQ made by the RND company.
Portico5043
This models an analog compressor/limiter made by the RND company.
LIM.ATK 0-120 ms Attack time of the limiter
LIM.REL
*1
Release time of the limiter
LIM.KNEE 0-5 Knee of the limiter
LIM.BYP OFF/ON Bypasses the limiter
PRESENCE -10 to +10
Positive (+) values lower the threshold of the high band and raise the
threshold of the low band. Negative (-) values do the opposite. If this is
set to 0, the high, mid, and low bands will be affected in the same way.
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Parameter Range Description
L-M XOVER 21.2 Hz-8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz-8.00 kHz Crossover frequency between the mid and high bands
SLOPE -6 dB, -12 dB Filter slope
LOW GAIN -12.0 dB to +12.0 dB Low band gain
MID GAIN -12.0 dB to +12.0 dB Mid band gain
HI. GAIN -12.0 dB to +12.0 dB High band gain
TOTAL -72.0 dB to +12.0 dB Overall gain
CEILING -6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
LOW THRE -54.0 dB to 0.0 dB Threshold of the low band compressor
LOW RAT 1:1 to 20:1 Ratio of the low band compressor
LOW ATK 0-120 ms Attack time of the low band compressor
LOW REL
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Release time of the low band compressor
LOW KNEE 0-5 Knee of the low band compressor
LOW BYP OFF/ON Bypasses the low band compressor
MID THRE -54.0 dB to 0.0 dB Threshold of the mid band compressor
MID RAT 1:1 to 20:1 Ratio of the mid band compressor
MID ATK 0-120 ms Attack time of the mid band compressor
MID REL
*1
Release time of the mid band compressor
MID KNEE 0-5 Knee of the mid band compressor
MID BYP OFF/ON Bypasses the mid band compressor
HI. THRE -54.0 dB to 0.0 dB Threshold of the high band compressor
HI. RAT 1:1 to 20:1 Ratio of the high band compressor
HI. ATK 0-120 ms Attack time of the high band compressor
HI. RAT
*1
Release time of the high band compressor
HI. KNEE 0-5 Knee of the high band compressor
HI. BYP OFF/ON Bypasses the high band compressor
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
Parameter Range Description
Parameter Range Description
ALL BYPASS OFF, ON
Turns bypass on/off for the EQ. Even in the bypassed state, the signal will
pass through the input/output transformers and the amp circuit.
TRIM -12.0 to 12.0 dB Input gain
LF FREQ 30.00 to 300.0 Hz Center frequency of the LF band
LF GAIN -12.0 to 12.0 dB Gain of the LF band
LMF IN OFF, ON Switches the LMF band on/off
LMF Q 0.70 to 5.00 Q of the LMF band
LMF FREQ 50.00 to 400.0 Hz Center frequency of the LMF band
LMF GAIN -12.0 to 12.0 dB Gain of the LMF band
MF IN OFF, ON Switches the MF band on/off
MF Q 0.70 to 5.00 Q of the MF band
MF FREQ 330.0 to 2500 Hz Center frequency of the MF band
MF GAIN -12.0 to 12.0 dB Gain of the MF band
HMF IN OFF, ON Switches the HMF band on/off
HMF Q 0.70 to 5.00 Q of the HMF band
HMF FREQ 1.80k to 16.0k Hz Center frequency of the HMF band
HMF GAIN -12.0 to 12.0 dB Gain of the HMF band
LF/HF IN OFF, ON Switches the LF/HF bands on/off
HF FREQ 2.50k to 25.0k Hz Center frequency of the HF band
HF GAIN -12.0 to 12.0 dB Gain of the HF band
Parameter Range Description
IN OFF, ON
Turns bypass on/off for the compressor. When bypassed, the button will
be unlit. However even in the bypassed state, the signal will pass through
the input/output transformers and the amp circuit.
FB OFF, ON Switches between feed-forward type and feed-back type
THRESHOLD -50.0 to 0.0 dB Threshold level
RATIO 1.10 : 1 to 28.9 : 1, LIMIT Compression ratio
ATTACK 20 to 75 ms Attack time
RELEASE 100 ms to 2.50 sec Release time
GAIN -6.0 to 20.0 dB Output level