User Manual
Table Of Contents
- Utilisation du présent manuel de référence
- Table des matières
- Structure des fonctions
- Section SELECTED CHANNEL
- Section Centralogic
- Assignation des entrées et des sorties
- Assignation interne de la console CL et assignation du réseau audio Dante
- Modification des réglages d'assignation de sortie
- Modification des réglages d'assignation d'entrée
- Insertion d'un périphérique externe dans un canal
- Sortie directe d'un canal INPUT
- Enregistrement ou reproduction à l'aide d'un logiciel DAW sur l'ordinateur
- Canaux d'entrée
- Flux du signal des canaux d'entrée
- Spécification du nom et de l'icône de canal
- Réglages HA (Préampli micro)
- Envoi d'un signal depuis le canal d'entrée vers les bus STEREO/MONO
- Envoi d'un signal depuis un canal d'entrée vers un bus MIX/MATRIX
- Correction du retard des signaux entre les canaux (Input Delay)
- Opérations liées à la bibliothèque de canaux
- Canaux de sortie
- Le flux des signaux liés aux canaux de sortie
- Spécification du nom et de l'icône de canal
- Envoi de signaux depuis les canaux MIX vers le bus STEREO/MONO
- Envoi de signaux depuis les canaux MIX et STEREO/MONO vers les bus MATRIX
- Correction du retard des signaux entre les canaux (Output Delay)
- Opérations liées à la bibliothèque de canaux
- EQ et dynamiques
- Groupement et liaison
- Mémoire de scènes
- À propos des mémoires de scènes
- Utilisation des mémoires de scènes
- Édition des mémoires de scènes
- Utilisation de la fonction Global Paste
- Utilisation de la fonction Focus
- Utilisation de la fonction Recall Safe
- Utilisation de la fonction Fade
- Émission en sortie d'un signal de contrôle vers un périphérique externe en tandem avec un rappel de scène (GPI OUT)
- Reproduction d'un fichier audio lié à un rappel de scène
- Fonctions Monitor et Cue
- Fonctions Talkback et Oscillator
- Indicateurs de niveau
- Égaliseur graphique, effets et Premium Rack
- Rack d'E/S et préampli micro externe
- MIDI
- Fonctionnalité MIDI de la console de série CL
- Réglages MIDI de base
- Utilisation des changements de programme pour rappeler des scènes et des éléments de la bibliothèque
- Utilisation des changements de commande pour contrôler les paramètres
- Utilisation des changements de paramètre pour contrôler les paramètres
- Réglages utilisateur liés à la (sécurité)
- Réglages User Level
- Préférences
- Touches USER DEFINED KEYS
- USER DEFINED KNOBS
- Encodeurs attribuables
- Banque de faders personnalisés
- Fader principal
- Console Lock
- Sauvegarde et chargement des données de configuration vers et depuis un lecteur flash USB
- Chargement d'un fichier depuis le lecteur flash USB
- Formatage d'un lecteur flash USB
- Enregistreur
- Autres fonctions
- À propos de l'écran SETUP
- Réglages de l'horloge de mots et des logements
- Utilisation de connexions en cascade
- Réglages de base des bus MIX et MATRIX
- Réglage de la luminosité de l'écran tactile, des voyants DEL, de l'affichage des noms de canaux et des témoins
- Réglage de la date et de l'heure de l'horloge interne
- Réglage de l'adresse réseau
- Réinitialisation de l'unité sur les réglages d'usine par défaut
- Réglage du point de détection de l'écran tactile (fonction Calibration) (Calibrage)
- Réglage des faders (fonction Calibration)
- Réglage précis du gain d'entrée et de sortie (fonction Calibration)
- Réglage de la couleur du canal (fonction Calibration)
- Réglages du réseau audio Dante
- Utilisation de l'interface GPI (General Purpose Interface - interface universelle)
- Annexes
- Liste des bibliothèques de l'égaliseur
- Liste des bibliothèques DYNAMICS
- Paramètres liés aux dynamiques
- Liste des types d'effets
- Paramètres d'effet
- Paramètres du processeur Rack Premium
- Synchronisation des effets et du tempo
- Paramètres pouvant être affectés à des changements de commandes
- Affectations de paramètre NRPN
- Application de l'opération aux paramètres de mixage
- Fonctions pouvant être affectées à des touches définies par l'utilisateur
- Fonctions pouvant être affectées à des boutons définis par l'utilisateur
- Fonctions pouvant être affectées à des encodeurs attribuables
- Format des données MIDI
- Messages d'erreur et d'avertissement
- Caractéristiques électriques
- Paramètres de base de la console
- M IDI Implementation Chart
- Index
Annexes
Manuel de référence
254
4.8 FUNCTION CALL – CHANNEL –
4.8.1 Pair ON/OFF Trigger Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number of both [Rx CH] and SUB STATUS are
matched. The data will be echoed when [PARAMETER CHANGE ECHO] is on.
4.8.2 Module Name
*1) 0 :CH1 - 71:CH72
256 :MIX 1 - 279:MIX 24
512 :MATRIX 1 - 519: MATRIX 8
4.9 LEVEL METER DATA
4.9.1 Format (PARAMETER CHANGE)
When transmission is enabled by receiving Request for Level Meter, the corresponding metering data will be sent in every 50
millisecond for 10 seconds. If metering information is expected to be continuously sent, Request is needed to be sent in at least every
10 seconds.
Receive
The data will be echoed when [PARAMETER CHANGE ECHO] is ON.
Transmission
When transmission is enabled by receiving Request, the corresponding metering data will be sent in constant interval for a given
period of time (The interval and time will vary depending on devices). When rebooted or port setting is changed, the transmission
will be disabled.
When [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
4.9.2 Format (PARAMETER REQUEST)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number of both [Rx CH] and SUB STATUS are
matched. The data will be echoed when [PARAMETER CHANGE ECHO] is on. the corresponding metering data will be sent via
[Rx CH] in constant interval for a given period of time (The interval and time will vary depending on devices).
When Address UL = 0x7F is received, all metering data transmission will be immediately stopped [disabled].
Transmission
When [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Série CL
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01000011 "C"
01101000 "h"
01101100 "l"
01010000 "P"
01101001 "i"
01110010 "r"
01000011 "C"
01110000 "p"
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0sssssss sh
Source Channel Number H *1)
0sssssss sl
Source Channel Number L *1)
0ddddddd dh
Destination Channel Number H *1)
0ddddddd dl
Destination Channel Number L *1)
EOX 11110111 F7
End of exclusive
Module Name
Pair On (with Copy) “PAIRONCP”
Pair On (with Reset Both) “PAIRONRS”
Pair Off “PAIROFF_”
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Série CL
DATA CATEGORY 00100001 21
REMOTE LEVEL METER
DATA 0mmmmmmm mm
ADDRESS UL
0mmmmmmm mm
ADDRESS LU
0mmmmmmm mm
ADDRESS LL
0ddddddd dd
Data1
::
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0011nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Série CL
DATA CATEGORY 00100001 21
REMOTE LEVEL METER
DATA 0mmmmmmm mm
ADDRESS UL
0mmmmmmm mm
ADDRESS LU
0mmmmmmm mm
ADDRESS LL
0ccccccc ch
Count H
0ccccccc cl
Count L
EOX 11110111 F7
End of exclusive