User Manual
Table Of Contents
- 如何使用本参考说明书
- 目录
- 功能树
- SELECTED CHANNEL(选定通道)部分
- Centralogic(中央逻辑)部分
- 输入和输出跳线
- 输入通道
- 输出通道
- EQ和动态
- 通道操作
- 场景记忆
- 监听和提示功能
- 对讲和振荡器
- 电平表
- 图形EQ、参数EQ、效果和PREMIUM RACK
- I/O设备和外接前级放大器
- MIDI
- 录音机
- 设置
- 关于SETUP画面
- 用户设置
- 偏好设置
- USER DEFINED键
- 可以分配到USER DEFINED键的功能
- USER DEFINED旋钮
- 可以分配到USER DEFINED旋钮的功能
- 可分配编码器
- 能指定到可分配编码器的功能
- GAIN/PAN/ASSIGN旋钮(可分配编码器)功能
- 自定义推子库
- 主推子
- 自定义推子库功能
- 调音台锁定
- 将设置数据保存到USB闪存以及从USB中载入
- 格式化USB闪存
- 字时钟和插槽设置
- 使用级联连接
- MIX总线和MATRIX总线的基本设置
- 打开/关闭整个幻象电源的供电
- 指定触摸屏、LED、通道名称画面和照明灯的亮度
- 设定内部时钟的日期和时间
- 设置网络地址
- Dante音频网络设置
- Dante Device Lock
- 支持Dante Domain Manager
- 使用GPI(通用接口)
- 帮助功能
- 其它功能
- 警告/出错信息
- 索引
- Data List
Data List
15
REV+SYMPHO.
One input, two output reverb and symphonic effects in parallel.
REVSYMPHO.
One input, two output reverb and symphonic effects in series.
REVPAN
This is a 1-in/2-out series-connected reverb and auto-pan effect.
DELAY+ER.
One input, two output delay and early reflections effects in parallel.
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV/SYM 0-100%
Reverb and symphonic balance
(0% = all reverb, 100% = all symphonic)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and symphonic reverb balance
(0% = all symphonic reverb, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and panned reverb balance (0% = all panned reverb, 100% = all
reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
DIR.
*1
*1. LR, LR, LR, Turn L, Turn R
Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
DLY/ER 0-100%
Delay and early reflections balance (0% = all delay, 100% = all early
reflections)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
TYPE
S-Hall, L-Hall, Random,
Revers, Plate, Spring
Type of early reflection simulation
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reflection density
ER NUM. 1-19 Number of early reflections
SYNC OFF/ON
Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY