User Manual
Table Of Contents
- Como usar este Manual de Referência
- Sumário
- Árvore de funções
- Seção SELECTED CHANNEL (canal selecionado)
- Seção Centralogic
- Patch de entrada e saída
- Canais de entrada
- Fluxo do sinal para canais de entrada
- Especificando o nome/ícone do canal
- Configurações do HA (amplificador com cabeça)
- Enviando o sinal de um canal de entrada para o barramento STEREO/MONO
- Função de panorâmica adicionada (apenas canais de entrada mono)
- Enviando um sinal de um canal de entrada para um barramento MIX/MATRIX
- Indicação no visor do nome do canal
- Correção do atraso entre os canais (Input Delay)
- Saída surround para canais de entrada
- Operações da biblioteca de canais
- Canais OUTPUT
- EQ (equalizador) e dinâmica
- Trabalho de canal
- Memória de cena
- Armazenando e chamando cenas
- Edição de memórias de cena
- Uso da função Global Paste
- Usando a função Focus Recall
- Uso da função Fade
- Emitindo um sinal de controle para um dispositivo externo junto com a chamada de cena (GPI OUT)
- Reproduzindo um arquivo de áudio vinculado a uma chamada de cena
- Uso do modo de visualização
- Funções Monitor e Cue
- Talkback e Oscilador
- Medidores
- EQ gráfico, EQ paramétrico, efeitos e PREMIUM RACK
- Dispositivos de E/S e amplificadores com cabeça externos
- MIDI
- Gravador
- Configuração
- Sobre a tela SETUP (configuração)
- Configurações do usuário
- Preferências
- Teclas USER DEFINED
- Funções que podem ser atribuídas às teclas USER DEFINED
- Botões giratórios USER DEFINED
- Funções que podem ser atribuídas a botões giratórios USER DEFINED
- Codificadores atribuíveis
- Funções que podem ser atribuídas a codificadores atribuíveis
- Funções do botão giratório GAIN/PAN/ASSIGN (codificador atribuível)
- Banco de atenuadores personalizados
- Master Fader (atenuador mestre)
- Funções do banco de atenuadores personalizados
- Console Lock (bloqueio do console)
- Salvando e carregando dados de configuração de uma unidade flash USB
- Formatação de uma unidade flash USB
- Função de remontagem adicionada a unidades flash USB
- Configurações do Word Clock e dos compartimentos
- Usando conexões em cascata
- Configurações básicas dos barramentos MIX e MATRIX
- Como ligar/desligar toda a fonte de alimentação phantom
- Especificando o brilho da tela sensível ao toque, LEDs, visores de nome de canal e lâmpadas
- Definição da data e da hora do relógio interno
- Configuração do endereço de rede
- Configurações da rede de áudio Dante
- Dante Device Lock
- Compatibilidade com o Dante Domain Manager
- Uso da GPI (General Purpose Interface)
- Função Help (ajuda)
- Outras funções
- Inicializando a unidade com as configurações padrão de fábrica
- Ajustando o ponto de detecção da tela sensível ao toque (função Calibration (calibração))
- Ajustando os atenuadores (função Calibration)
- Fazendo ajustes finos no ganho de entrada e saída (função Calibration)
- Ajustando a cor do canal (função Calibration)
- Como ajustar o brilho do visor de nome do canal
- Como ajustar o contraste do visor de nome do canal
- Inicializando as configurações do console e da rede de áudio Dante
- Procedimento de atualização alterado para o firmware NAME SUB CPU
- Função de atualização adicionada ao firmware Dante
- Mensagens de advertência/erro
- Índice remissivo
- Data List
Data List
10
MOD. DELAY
One input, two output basic repeat delay with modulation.
DELAY LCR
One input, two output 3-tap delay (left, center, right).
ECHO
Two input, two output stereo delay with crossed feedback loop.
CHORUS
Two input, two output chorus effect.
Parameter Range Description
DELAY 0.0-2725.0 ms Delay time
FB. GAIN -99 to +99% Feedback gain
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
WAVE Sine/Tri Modulation waveform
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine DELAY
MOD.NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
DELAY L 0.0-2730.0 ms Left channel delay time
DELAY C 0.0-2730.0 ms Center channel delay time
DELAY R 0.0-2730.0 ms Right channel delay time
FB. DLY 0.0-2730.0 ms Feedback delay time
LEVEL L -100 to +100% Left channel delay level
LEVEL C -100 to +100% Center channel delay level
LEVEL R -100 to +100% Right channel delay level
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE C
*1
Used in conjunction with TEMPO to determine center channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Parameter Range Description
DELAY L 0.0-1350.0 ms Left channel delay time
DELAY R 0.0-1350.0 ms Right channel delay time
FB.DLY L 0.0-1350.0 ms Left channel feedback delay time
FB.DLY R 0.0-1350.0 ms Right channel feedback delay time
FB. G L -99 to +99%
Left channel feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
FB. G R -99 to +99%
Right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
LR FBG -99 to +99%
Left to right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
RL FBG -99 to +99%
Right to left channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FBL
*1
Used in conjunction with TEMPO to determine left channel feedback
DELAY
NOTE FBR
*1
Used in conjunction with TEMPO to determine right channel feedback
DELAY
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
AM DEPTH 0-100% Amplitude modulation depth
PM DEPTH 0-100% Pitch modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain