User Manual
Table Of Contents
- Cómo usar este Manual de referencia
- Contenido
- Árbol de funciones
- Sección SELECTED CHANNEL (Canal seleccionado)
- Sección Centralogic
- Asignación de patches de entrada y salida
- Asignación de patches interna de consola CL y asignación de patches de red de audio Dante
- Modificación de los ajustes del patch de salida
- Modificación de los ajustes del patch de entrada
- Inserción de un dispositivo externo en un canal
- Salida directa de un canal INPUT
- Grabación o reproducción mediante DAW en un equipo
- Canales de entrada
- Flujo de la señal de los canales de entrada
- Especificación del nombre e icono del canal
- Introducción de ajustes HA (Head Amp)
- Envío de una señal desde un canal de entrada a los buses STEREO/MONO (estéreo/mono)
- Envío de una señal desde un canal de entrada a un bus MIX/MATRIX
- Corrección del retardo entre canales (Retardo de entrada)
- Operaciones de las bibliotecas de canales
- Canales de salida
- Flujo de la señal de los canales de salida
- Especificación del nombre e icono del canal
- Envío de señales desde los canales MIX al bus STEREO/MONO
- Envío de señales desde los canales MIX y STEREO/ MONO a los buses MATRIX
- Corrección del retardo entre canales (Retardo de salida)
- Operaciones de las bibliotecas de canales
- EQ y dinámica
- Agrupamiento y enlace
- Memoria de escenas
- Acerca de las memorias de escenas
- Uso de las memorias de escenas
- Edición de memorias de escena
- Uso de la función Global Paste
- Uso de la función Focus
- Utilización de la función Recall Safe
- Utilización de la función Fade
- Envío de una señal de control a un dispositivo externo en combinación con la recuperación de una escena (GPI OUT)
- Reproducción de un archivo de audio que enlaza a una recuperación de escena
- Funciones Monitor (Monitorización) y Cue (Escucha)
- Interfono y oscilador
- Medidores
- Bastidor de ecualizador gráfico, efectos y Premium Rack
- Bastidor E/S y amplificador principal externo
- MIDI
- Ajustes del usuario (seguridad)
- Ajustes de nivel de usuario
- Preferencias
- Teclas USER DEFINED
- Mandos USER DEFINED
- Codificadores asignables
- Banco de faders personalizado
- Fader principal
- Bloqueo de consola
- Guardar y cargar datos de configuración de una unidad flash USB
- Carga de un archivo desde la unidad flash USB
- Formateo de una unidad flash USB
- Grabadora
- Otras funciones
- Acerca de la pantalla SETUP (Configurar)
- Ajustes del reloj y ranura
- Uso de las conexiones en cascada
- Ajustes básicos de los buses MIX y MATRIX
- Especificación del brillo de la pantalla táctil, los indicadores LED, las pantallas de nombre de canal y las lámparas
- Configuración de la fecha y la hora del reloj interno
- Configuración de la dirección de red
- Inicialización de la unidad a los ajustes predeterminados de fábrica
- Ajuste del punto de detección de la pantalla táctil (función Calibration)
- Ajuste de los faders (función de calibración)
- Ajuste preciso de la ganancia de entrada y salida (Función de calibración)
- Ajuste del color de canal (función de calibración)
- Ajustes de la red de audio Dante
- Uso de GPI (interfaz de finalidad general)
- Apéndices
- Lista de la biblioteca EQ
- Lista de la biblioteca DYNAMICS
- Parámetros de dinámicas
- Lista de tipos de efecto
- Parámetros de efectos
- Parámetros de procesador de bastidor Premium
- Sincronización de efectos y tempo
- Parámetros que se pueden asignar para controlar los cambios
- Asignaciones de parámetros NRPN
- Operación de parámetros de mezcla, aplicabilidad
- Funciones que pueden asignarse a las teclas definidas por el usuario
- Funciones que pueden asignarse a los mandos definidos por el usuario
- Funciones que se pueden asignar a los codificadores asignables
- Formato de datos MIDI
- Mensajes de advertencia/error
- Características eléctricas
- Parámetros básicos del mezclador
- I mplementación MIDI
- Índice
Apéndices
Manual de referencia
250
[Conversion from actual data to bulk data]
d[0-6]: actual data
b[0-7]: bulk data
b[0] = 0;
for( I=0; I<7; I++){
if( d[I]&0x80){
b[0] |= 1<<(6-I);
}
b[I+1] = d[I]&0x7F;
}
[Recovery from bulk data to actual data]
d[0-6]: actual data
b[0-7]: bulk data
for( I=0; I<7; I++){
b[0] <<= 1;
d[I] = b[I+1]+(0x80&b[0]);
}
3.3 PARAMETER CHANGE
Reception
This message is echoed if [PARAMETER CHANGE ECHO] is ON.
This message is received if [PARAMETER CHANGE Rx] is ON and [Rx CH] matches
the Device number included in the SUB STATUS. When a PARAMETER CHANGE is
received, the specified parameter will be controlled. When a PARAMETER REQUEST
is received, the current value of the specified parameter will be transmitted as a
PARAMETER CHANGE with its Device Number as the [Rx CH].
Transmission
If [PARAMETER CHANGE Tx] is ON, and you edit a parameter for which CONTROL
CHANGE transmission has not been enabled, a PARAMETER CHANGE will be
transmitted with the [Tx CH] as its device number.
In response to a PARAMETER REQUEST, a PARAMETER CHANGE will be
transmitted with [Rx CH] as its device number.
4 PARAMETER CHANGE details
4.1 CURRENT SCENE, SETUP, BACKUP, USER SETUP
4.1.1 Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] in [Tx CH] when [PARAMETER
CHANGE Tx] is on and the parameter is not registered on the [CONTROL CHANGE
EVENT LIST].
4.1.2 Format (PARAMETER REQUEST)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
via PARAMETER CHANGE immediately the data is received.
4.1.3 Data category
4.2 FUNCTION CALL – LIBRARY STORE, RECALL –
4.2.1 Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding parameter will be changed
immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] (MIDI CH) in [Tx CH] when
[PARAMETER CHANGE Tx] is on.
4.2.2 Function Name
Command rx/tx Function
F0 43 1n 3E 19 … F7
RARAMETER CHANGE
rx/tx
CL series native parameter change
F0 43 3n 3E 19 … F7
PARAMETER REQUEST
rx/tx
CL series native parameter request
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Serie CL
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
0ddddddd dd
Data
: :
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Serie CL
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
EOX 11110111 F7
End of exclusive
Data Category Name
0x01 00000001
Current Scene /Setup/Backup/
User Setup Data
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Serie CL
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 "L"
(ASCII CODE)
01101001 "i"
(ASCII CODE)
01100010 "b"
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Number High
0nnnnnnn nl
Number Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
EOX 11110111 F7
End of exclusive
Function Name
Store “LibStr__”
Recall “LibRcl__”
Unknown Factor Store “LibUnStr”
Unknown Factor Recall “LibUnRcl”
Store Undo (only Score) “LibStrUd”
Recall Undo (only Scene) “LibRclUd”