User Manual
Table Of Contents
- Cómo usar este Manual de referencia
- Contenido
- Árbol de funciones
- Sección SELECTED CHANNEL (Canal seleccionado)
- Sección Centralogic
- Asignación de patches de entrada y salida
- Asignación de patches interna de consola CL y asignación de patches de red de audio Dante
- Modificación de los ajustes del patch de salida
- Modificación de los ajustes del patch de entrada
- Inserción de un dispositivo externo en un canal
- Salida directa de un canal INPUT
- Grabación o reproducción mediante DAW en un equipo
- Canales de entrada
- Flujo de la señal de los canales de entrada
- Especificación del nombre e icono del canal
- Introducción de ajustes HA (Head Amp)
- Envío de una señal desde un canal de entrada a los buses STEREO/MONO (estéreo/mono)
- Envío de una señal desde un canal de entrada a un bus MIX/MATRIX
- Corrección del retardo entre canales (Retardo de entrada)
- Operaciones de las bibliotecas de canales
- Canales de salida
- Flujo de la señal de los canales de salida
- Especificación del nombre e icono del canal
- Envío de señales desde los canales MIX al bus STEREO/MONO
- Envío de señales desde los canales MIX y STEREO/ MONO a los buses MATRIX
- Corrección del retardo entre canales (Retardo de salida)
- Operaciones de las bibliotecas de canales
- EQ y dinámica
- Agrupamiento y enlace
- Memoria de escenas
- Acerca de las memorias de escenas
- Uso de las memorias de escenas
- Edición de memorias de escena
- Uso de la función Global Paste
- Uso de la función Focus
- Utilización de la función Recall Safe
- Utilización de la función Fade
- Envío de una señal de control a un dispositivo externo en combinación con la recuperación de una escena (GPI OUT)
- Reproducción de un archivo de audio que enlaza a una recuperación de escena
- Funciones Monitor (Monitorización) y Cue (Escucha)
- Interfono y oscilador
- Medidores
- Bastidor de ecualizador gráfico, efectos y Premium Rack
- Bastidor E/S y amplificador principal externo
- MIDI
- Ajustes del usuario (seguridad)
- Ajustes de nivel de usuario
- Preferencias
- Teclas USER DEFINED
- Mandos USER DEFINED
- Codificadores asignables
- Banco de faders personalizado
- Fader principal
- Bloqueo de consola
- Guardar y cargar datos de configuración de una unidad flash USB
- Carga de un archivo desde la unidad flash USB
- Formateo de una unidad flash USB
- Grabadora
- Otras funciones
- Acerca de la pantalla SETUP (Configurar)
- Ajustes del reloj y ranura
- Uso de las conexiones en cascada
- Ajustes básicos de los buses MIX y MATRIX
- Especificación del brillo de la pantalla táctil, los indicadores LED, las pantallas de nombre de canal y las lámparas
- Configuración de la fecha y la hora del reloj interno
- Configuración de la dirección de red
- Inicialización de la unidad a los ajustes predeterminados de fábrica
- Ajuste del punto de detección de la pantalla táctil (función Calibration)
- Ajuste de los faders (función de calibración)
- Ajuste preciso de la ganancia de entrada y salida (Función de calibración)
- Ajuste del color de canal (función de calibración)
- Ajustes de la red de audio Dante
- Uso de GPI (interfaz de finalidad general)
- Apéndices
- Lista de la biblioteca EQ
- Lista de la biblioteca DYNAMICS
- Parámetros de dinámicas
- Lista de tipos de efecto
- Parámetros de efectos
- Parámetros de procesador de bastidor Premium
- Sincronización de efectos y tempo
- Parámetros que se pueden asignar para controlar los cambios
- Asignaciones de parámetros NRPN
- Operación de parámetros de mezcla, aplicabilidad
- Funciones que pueden asignarse a las teclas definidas por el usuario
- Funciones que pueden asignarse a los mandos definidos por el usuario
- Funciones que se pueden asignar a los codificadores asignables
- Formato de datos MIDI
- Mensajes de advertencia/error
- Características eléctricas
- Parámetros básicos del mezclador
- I mplementación MIDI
- Índice
Apéndices
Manual de referencia
251
4.2.3 Module Name
*1) 0:CH1 – 71:CH72
72:ST IN 1L – 87:ST IN 8R
*2) 256:MIX 1 – 279:MIX 24
*3) 512:MATRIX 1 – 519: MATRIX 8
*4) 1024:STEREO L – 1026:STEREO C
*5) 512:will be used if the recalling or storing data is only one.
*6) 0: GEQ1A, 1: GEQ1B, 2: GEQ2A, … 36: GEQ19A, 37:GEQ19B
38: EFFECT GEQ1A, 39: EFFECT GEQ1B,
40: EFFECT GEQ2A, … 52: EFFECT GEQ8A, 53: EFFECT GEQ8B
*7) 0:Effect1- 7:Effect8
*8) 1280:CH1 – 1351:CH72
1352:ST IN 1L – 1367:ST IN 8R
*9) 0: Premium Rack 1A, 1: Premium Rack 1B,
2: Premium Rack 2A, … 14: Premium Rack 8A, 15: Premium Rack 8B
4.3 FUNCTION CALL – LIBRARY EDIT –
4.3.1 Format (PARAMETER CHANGE)
Receive
Data will be received when [PARAMETER CHANGE Rx] is on and the Device number
of both [Rx CH] and SUB STATUS are matched. The data will be echoed when
[PARAMETER CHANGE ECHO] is on. The corresponding memory/library will be
changed immediately the data is received.
Transmission
PARAMETER CHANGE will be sent in reply to Request. If [PARAMETER CHANGE
ECHO] is on, the message will be sent as it is.
4.3.2 Function Name
4.3.3 Module Name
Module Name
Scene “SCENE___”
Input EQ “INEQ____”
Output EQ “OUTEQ___”
Dynamics “DYNA____”
Input CH “INCHNNL_”
Output CH “OUTCHNNL”
GEQ “GEQ_____”
Effect “EFFECT__”
Portico5033 “P5033___”
Portico5043 “P5043___”
U76 “U76_____”
Opt-2A “OPT-2A__”
EQP-1A “EQ-1A___”
DynamicEQ “DYNAEQ__”
Dante Input Patch “DANTEIN_”
Function Number Channel*1) tx/rx
“LibStr__” SCENE 1-300 *5)
tx/rx
INPUT EQ LIB 41-199 *1)
tx/rx
OUTPUT EQ LIB 4-199 *2) *3) *4)
tx/rx
Dynamics LIB 42-199 *1) *2) *3) *4) *8)
tx/rx
INPUT CH LIB 1-199 *1)
tx/rx
OUTPUT CH LIB 1-199 *2) *3) *4)
tx/rx
GEQ LIB 1-199 *6)
tx/rx
EFFECT LIB 28-199 *7)
tx/rx
Premium Effect LIB 1-100 *9)
tx/rx
Dante Input Patch LIB 1-10 *5)
tx/rx
“LibUnStr” SCENE 1-300 0
tx
INPUT EQ LIB 41-199 0
tx
OUTPUT EQ LIB 4-199 0
tx
Dynamics LIB 42-199 0
tx
INPUT CH LIB 1-199 0
tx
OUTPUT CH LIB 1-199 0
tx
GEQ LIB 1-199 0
tx
EFFECT LIB 28-199 0
tx
Premium Effect LIB 1-100 0
tx
Dante Input Patch LIB 1-10 0
tx
“LibRcl__” SCENE 0-300 *5)
tx/rx
INPUT EQ LIB 1-199 *1)
tx/rx
OUTPUT EQ LIB 1-199 *2) *3) *4)
tx/rx
Dynamics LIB 1-199 *1) *2) *3) *4) *8)
tx/rx
INPUT CH LIB 0-199 *1)
tx/rx
OUTPUT CH LIB 0-199 *2) *3) *4)
tx/rx
GEQ LIB 0-199 *6)
tx/rx
EFFECT LIB 1-199 *7)
tx/rx
Premium Effect LIB 0-100 *9)
tx/rx
Dante Input Patch LIB 0-10 *5)
tx/rx
“LibUnRcl” SCENE 0 *5)
tx
INPUT EQ LIB 0 *1)
tx
OUTPUT EQ LIB 0 *2) *3) *4)
tx
Dynamics LIB 0 *1) *2) *3) *4) *8)
tx
INPUT CH LIB 0 *1)
tx
OUTPUT CH LIB 0 *2) *3) *4)
tx
GEQ LIB 0 *6)
tx
EFFECT LIB 0 *7)
tx
Premium Effect LIB 0 *9)
tx
Dante Input Patch LIB 0 *5)
tx
“LibStrUd” SCENE 0 0
“LibRclUd” SCENE 0 0
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacture’s ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00010010 19
Serie CL
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 "L"
(ASCII CODE)
01101001 "i"
(ASCII CODE)
01100010 "b"
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE).
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
Function Number Channel*1) tx/rx
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0sssssss sh
number -source start High
0sssssss sl
number -source start Low
0eeeeeee eh
number -source end High
0eeeeeee el
number -source end Low
0ddddddd dh
number -destination start High
0ddddddd dl
number -destination to start Low
EOX 11110111 F7
End of exclusive
Function Name
Copy “LibCpy__”
Paste “LibPst__”
Clear “LibClr__”
Cut “LibCut__”
Insert “LibIns__”
Edit Undo “LibEdtUd”
Module Name Function
SCENE LIB “SCENE___” Copy, Paste, Clear, Cut, Insert, EditUndo
INPUT EQ LIB “INEQ____” Clear Only
OUTPUT EQ LIB “OUTEQ___” Clear Only
Dynamics LIB “DYNA____” Clear Only
INPUT CH LIB “INCHNNL_” Clear Only
OUTPUT CH LIB “OUTCHNNL” Clear Only
GEQ LIB “GEQ_____” Clear Only
EFFECT LIB “EFFECT__” Clear Only
Portico5033 LIB “P5033___” Clear Only
Portico5043 LIB “P5043___” Clear Only
U76 LIB “U76_____” Clear Only
Opt-2A LIB “OPT-2A__” Clear Only
EQP-1A LIB “EQ-1A___” Clear Only
DynamicEQ LIB “DYNAEQ__” Clear Only
Dante Input Patch LIB “DANTEIN_” Clear Only