User Manual
Table Of Contents
- PRECAUTIONS
- Contents
- Introduction
- System Overview
- About Dante
- About Connections
- Part Names & Functions
- Power Supply
- Installing and Removing Optional Cards
- Touch Screen
- Quick Guide
- Basic system configuration
- Installing an optional card
- Setting the Unit ID
- Connecting the devices
- Turning on the power to the RIVAGE PM10 system
- Setting the word clock
- Assigning channels to the TWINLANe network
- Patching the input ports
- Patching the output ports
- Setting the analog gain for HA (Head Amp)
- Sending an input channel signal to the STEREO bus
- Check list
- Other Operations
- Troubleshooting
- Specifications (CS-R10, CS-R10-S)
- Index
RIVAGE PM10 System Setup Guide
49
General Specifications
At the time of measurement, all faders are set to nominal. Output impedance of the signal generator is 150Ω.
Frequency response
Fs= 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz @20 Hz–20 kHz, reference to the nominal output level @1 kHz
Total harmonic distortion
Fs= 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
* An 80kHz, 18 dB/octave low pass filter is used to measure total harmonic distortion.
Hum & noise
*2
Fs= 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Dynamic range
Fs= 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
* An IHF-A filter is used to measure dynamic range.
Specifications (CS-R10, CS-R10-S)
Inputs Outputs RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600Ω GAIN: +66 dB –0.8 0.0 0.5 dB
Inputs Outputs RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600Ω +4 dBu@20 Hz–20 kHz, GAIN: +66 dB 0.12 %
OMNI IN 1-8 OMNI OUT 1-8 600Ω +4 dBu@20 Hz–20 kHz, GAIN: –6 dB 0.05 %
Internal OSC OMNI OUT 1-8 600Ω Full scale output @1 kHz 0.02 %
Internal OSC PHONES
8Ω
Full scale output @1 kHz,
phones level control: max.
0.2 %
Inputs Outputs RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8
600Ω
Rs= 150Ω, GAIN: +66 dB
Master fader at nominal level and one
Ch fader at nominal level.
–128
EIN
*1
*1. EIN stands for Equivalent Input Noise.
*2. An IHF-A filter is used to measure hum & noise level.
dBu
–62 dBu
OMNI IN 1-8 OMNI OUT 1-8
600Ω
Rs= 150Ω, GAIN: –6 dB
Master fader at nominal level and one
Ch fader at nominal level.
–90 -85 dBu
All Inputs OMNI OUT 1-8
600Ω
Rs= 150Ω, GAIN: –6 dB
Master fader at nominal level and all
OMNI IN1-8 in faders at nominal level.
-76 dBu
— OMNI OUT 1-8 600Ω Residual output noise, ST master off. –92 dBu
—
PHONES
8Ω
Residual output noise, phones level
control min.
–88 dBu
Inputs Outputs RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600Ω AD + DA, GAIN: –6 dB 114 dB
— OMNI OUT 1-8 600Ω DA Converter 116 dB