User Manual

Effects Parameters
9 RIVAGE PM series Data List
■ VSS4HD
*4
Room simulation reverb by the TC Electronic. A variety of reflection settings provide a
musicalsounding reverberation that gives you detailed control of room size and distance to the walls.
■ NonLin 2
*3
Stereo reverb effect by the TC Electronic. As a gate reverb that uses an envelope filter and does not
require a trigger, this can be used in a variety of creative applications.
■ Bricasti Design Y7 Stereo Reverb Processor
A reverb plug-in jointly developed by Bricasti Design and Yamaha.
Parameter Range Description
Decay (MDecay
*1
)
*1. Actual indication in the screen encoder access field
0.10 to 20.0 s Decay time of the reverb
Pre Delay 5 to 300 ms Delay of the reverb input
Hi Cut 20.00 Hz to 20.0 kHz Frequency of the high cut filter at the input stage of the reverb
Rev Delay 0 to 300 ms Delay of the reverb tail
Rev Size 0 to 15 Perceptual size of the reverb
Rev Width –10 to 10 Width of the reverb tail
Decrease (ER Dec
*1
)
0–100 % Number of reflections for the early reflections
Lo Color –50 to 50 Low-frequency range of the early reflections
Hi Color –50 to 50 High-frequency range of the early reflections
Early Start 0–100 %
Start point of early reflection. Removes the first part of early
reflection.
Early Stop 0–100 %
End point of the early reflection. Attenuates the end of early
reflection pattern.
Location Type
*2
*2. Oval Room, Cinema, Church, Castle Hall, Theater, Living Room, Parking Garage, Bathroom, Viennna Hall,
Concert Hall, Jazz Club
Type of location
Source 1/2 L30 to R 30 Position of input sources 1/2
In Level OFF, –97.0 to 0.0 dB Input level
Out Level OFF, –97.0 to 0.0 dB Output level
Mute Input OFF, ON Mutes the input
Mute Output OFF, ON Mutes the output
Lo Cut 20.00 to 200.0 Hz Low-cut frequency
Lo Damp –18.0 0.0 dB Low-cut amount
Hi Soften 50 to 50 High-frequency range of the reverb tail
Lo Decay 0.01 to 2.50 Multiple of decay for the frequency range below Lo Xover
Lo Mid Decay 0.01 to 2.50 Multiple of decay for the low-mid frequency range
Hi Mid Decay 0.01 to 2.50 Multiple of decay for the middle frequency range
Hi Decay 0.01 to 2.50 Multiple of decay for the frequency range above Hi Xover
Lo Xover 20.00 to 500.0 Hz
Crossover frequency between the low and low-mid frequency
ranges of the reverb tail
Mid Xover 20.00 Hz to 2.00 kHz
Crossover frequency between the low-mid and middle
frequency ranges of the reverb tail
Hi Xover 500.0 Hz to 20.0 kHz
Crossover frequency between the middle and high frequency
ranges of the reverb tail
Reverb Type Colored, Normal Type of reverb effect
Reverb Diffuse –25 to 25 Diffusion for the decay time
Modulation Type
*3
*3. Sync, Chaos, Counter Clockwise, Clockwise, Left/Right, Front/Rear Diffuse, Front/Rear Subtle, Front/Rear,
Default, Off
*4. Only for DSP-R10
Type of modulation
Mod. Rate –50 to 50 Rate of modulation
Mod. Depth –0 to 200 Depth of modulation
Dry Level OFF, –97.0 to 0.0 dB Level of the dry signal at the output stage
Parameter Range Description
Pre Delay 5–500 ms Delay of the envelope
Attack 0–309 ms Attack time of the envelope
Hold 10–85 ms Hold time of the envelope
Release 0–106 ms Release time of the envelope
Style
*1
*1. NonLin Decayed, Explode, Gated, Rough, Air Ambience, Small Ambience, Live, Wild, Hollow, Box, Scanner,
Panner, Smooth B, Smooth A, Sustained, Mono To Stereo, NonLin Wide, NonLin B, NonLin A, NonLin Classic
Basic reverb style
Diffuse 0–100 % Diffusion (spread) for the reverb style
Type
*2
*2. Woolly, Woody, Ventilation, Tunnel, Synthetic, Spaceship, Radiator, Nextdoor, Muffled, Mouth, Moony, Levitate,
Kazoo, Hot Air, Guts, Digital, Chicken, Cave, Box, Aircon
*3. Only for DSP-R10
Type of Twist that affects the reverb
Ratio 0–100 % Proportion of Twist for the reverb
Lo Cut 20.00 Hz to 2.00 kHz Frequency of the low cut filter at the input stage of the reverb
Hi Cut 800.0 Hz to 20.0 kHz Frequency of the high cut filter at the input stage of the reverb
Width 0–100 % Stereo width of the output
In Level OFF, –119.5 to 0.0 dB Input level
Out Level OFF, –119.5 to 0.0 dB Output level
Dry Level OFF, –119.5 to 0.0 dB Level of the dry signal
Wet Level OFF, –119.5 to 0.0 dB Level of the wet signal (reverb component)
Parameter Range Description
Reverb Time 0.4 to 6.0 sec Adjusts the reverb time.
Pre Delay 0 to 600 mSec Adjusts the reverb input delay.
Size Small / Medium / Large Adjusts the size of the space.
RT Damping
Dark,1,2,3,4, Medium,
6,7,8,9, Bright
Adjusts the high frequency attenuation of the rear reverberation.
Rolloff
Dark,1,2,3,4, Medium,
6,7,8,9, Bright
Adjusts the LPF of the output section.
Rich ON / OFF Turn on this button to increase the density of the reverb.
High Diffusion ON / OFF Turn on this button to increase the amount of reverb spread.
VLF (Very Low
Frequency)
ON / OFF
Turn on this button to increase the reverb component in the ultra-low
range.
Bandpass ON / OFF Turns on BPF in the output section.
Presence ON / OFF Turn on this button to brighten the tone.
Dry / Wet 0 to 100 %
Adjusts the amount of mix between the input signal and the reverb
signal.
Lock ON / OFF
Turn on this button to lock Dry / Wet control so that it cannot be
changed.