User Manual

ManualsBrandsYamaha ManualsProfessional Audio MixersRIVAGE PM10

Table Of Contents

HY144-D-SRC Firmware Update Guide 1

■ Precautions

・ The user assumes full responsibility for the update.

・ Update the firmware components one device at a time.

・ Please note that the device may be damaged if you fail to follow these instructions

properly, or turn off the device or disconnect the cable while the update is in

progress.

・ If the update fails, and the device still does not operate correctly even after you

execute the update once again, please contact your Yamaha dealer.

・ This guide is the exclusive copyrights of Yamaha Corporation.

・ Audinate owns exclusive copyrights for the Dante firmware and its update program.

・ It is prohibited to duplicate or modify the firmware, software or this guide, in part or

in their entirety, without permission from the copyright owner.

・ The illustrations and screens as shown in this guide are for instructional purposes

only.

・ Yamaha Corporation makes no representations or warranties with regard to the use

of the software and documentation and cannot be held responsible for the results

of the use of this guide and the software.

・ Windows is a registered trademark of Microsoft ® Corporation in the United States

and other countries.

・ Mac is trademark of Apple Inc., registered in the U.S. and other countries.

・ The company names and product names in this guide are the trademarks or

registered trademarks of their respective companies.

・ Software may be revised and updated without prior notice.

■ Contents

Preparing for the update

.................................................... 2

Update procedure sequence ........................................... 2

Install the Dante Firmware Update Manager .................. 3

Computer TCP/IP setting ................................................. 4

Updating the firmware ..................................................... 6

About Failsafe Mode ....................................................... 10

Trouble shooting ............................................................ 14

SRC mode ........................................................................ 15

HY144-D-SRC Firmware Update Guide

Thank you for choosing a Yamaha product. This guide explains how to update the HY144-D-SRC

firmware. The SRC modes can be changed by updating to the card’s firmware corresponding to each

SRC mode (page 7).

Summary of content (15 pages)

PAGE 1
HY144-D-SRC Firmware Update Guide Thank you for choosing a Yamaha product. This guide explains how to update the HY144-D-SRC firmware. The SRC modes can be changed by updating to the card’s firmware corresponding to each SRC mode (page 7). ■ Precautions ・ The user assumes full responsibility for the update. ・ Update the firmware components one device at a time.
PAGE 2
Update procedure sequence Preparing for the update In order to update, you will need to prepare the following items. • A Windows or a Mac computer For the system requirements, refer to the Yamaha Pro Audio website. https://www.yamaha.com/proaudio/ • An Ethernet cable CAT5e or higher recommended. Straight or cross. • The HY144-D-SRC firmware update program Download the latest program from the following URL. https://www.yamaha.com/proaudio/ Update each firmware component in the following sequence.
PAGE 3
Install the Dante Firmware Update Manager Before you update the firmware, you must install the Dante Firmware Update Manager. Double-click the Dante Firmware Update Manager installer downloaded in “Preparing for the update” (Windows: DanteFirmwareUpdateManager-x.x.x.exe, Mac: DanteFirmwareUpdateManager-x.x.x.dmg) and follow the on-screen instructions to install the firmware. x.x.x represents the version number of the Dante Firmware Update Manager. In addition, extract the Dante firmware (extension: .
PAGE 4
Computer TCP/IP setting To update Dante firmware, configure computer TCP/IP settings. Windows 1. Open the “Network and Sharing Center” as described below. Windows 7 Select [Start] → [Control Panel], then click or 2. Click [Manage network connection] or [Change Adapter settings] from the “Tasks” list located in the left side of “Network and Sharing Center” window, then double-click [Local Area Connection]. The “Local Area Connection Status” dialog box will be displayed.
PAGE 5
NOTE The “User Account Control” dialog box may appear. Click [Continue] or [Yes]. 4. Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties]. The “Internet Protocol Version 4(TCP/IPv4) Properties” dialog box will be displayed. 5. Click [Obtain an IP address automatically]. Mac 1. Click [System Preferences] → [Network]. The “Network” dialog box will be displayed. 2. Click the service that you want to connect to the device.
PAGE 6
Updating the firmware Described below are the procedures to update the Dante module firmware integrated in the HY144-D-SRC. NOTE Perform the update with the HY144-D-SRC installed in the slot of a compatible device. 1. Connect the Dante [PRIMARY] connector of the HY144-D-SRC to the Ethernet connector on the computer using an Ethernet cable. 2. Turn on the power to the device to which the HY144-D-SRC is installed. 3.
PAGE 7
4. If you see the interface selection screen, select the interface card to connect the Dante device. 5. Click [Update Dante Firmware]. 6. Click [Browse] and select “FWUpdate_HY144-D-SRC _mode_vxxx_swyyy.dnt,” then click [Open]. mode represents the SRC mode name, xxx and yyy represent the firmware version number. NOTE Only alphanumeric characters, “-” (hyphen), and “_”(underscore) can be used in the path to save the Dante firmware.
PAGE 8
unselected, select this check box to allow access. If the update manager is blocked by the Windows firewall, the “Upgrade failed.” dialog box appears. NOTE If the HY144-D-SRC is not indicated, click [Refresh]. If it is still not indicated, check whether the cable might be disconnected or broken, whether the TCP/IP settings are correct or not, whether the device to which the HY144-DSRC is installed is running or not, and whether the HY144-DSRC is recognized by the Dante Controller. 9. Click [Start]. 8.
PAGE 9
HY144-D-SRC is installed, and restart the procedure from the step 3. If update still fails, follow the instructions stated in “About Failsafe Mode” to perform the recovery process. 10. Turn off the power to the device to which the HY144-D-SRC is installed, and then on again. NOTE Rapidly turning the unit on and off in succession can cause it to malfunction. After turning the unit off, wait for at least few seconds before turning it on again.
PAGE 10
About Failsafe Mode The Dante module integrated in the HY144-D- A Dante module that is in failsafe mode is shown SRC may become unusable due to data as a red device name in the network grid view of Dante Controller (version 3.1.x or later). corruption if the Dante device is powered-off during a firmware update. To recover from such a state, the Dante module will enter “failsafe mode.” To restore the Dante module from failsafe mode, a recovery image must be sent from the Dante Firmware Update Manager.
PAGE 11
Described below are the procedures to recover the Dante module integrated in the HY144-DSRC. 1. Turn off the power to the device to which the HY144-D-SRC is installed. 2. Separate the HY144-D-SRC from the Dante network. 3. Connect the Dante [PRIMARY] connector 4. Turn on the power to the device to which the HY144-D-SRC is installed. 5. Disable all but one of the network interfaces on your computer. You should also disable the wireless LAN. 6.
PAGE 12
7. If you see the interface selection screen, select the interface card to connect the Dante device. 8. Click [Failsafe Recovery]. 9. When the HY144-D-SRC is detected, click the [Stop Scan] button. If several minutes have passed without detection, check whether the cable might be disconnected or broken, whether the TCP/IP settings are correct or not, whether the device to which the HY144-D-SRC is installed 10. Select the check box of the detected HY144-D-SRC.
PAGE 13
11. Click [Start]. A pop-up is displayed confirming that you wish to proceed. 12. Click [OK] to start the recovery. Dante Firmware Update Manager will display “Processing Safe Recovery,” and then “Safe Recovery Done.” when the device(s) are recovered. 13. Exit the Dante Firmware Update Manager, and wait for two minutes before turning off the power to the device to which the HY144-D-SRC is installed. After recovery, the Dante module will be restarted.
PAGE 14
Trouble shooting • Is the Ethernet cable broken? Replace with an Ethernet cable which can communicate properly. • Are the network settings configured correctly? Check your computer settings (page 4). • Is there any resident security software installed? If the firewall function of anti-virus or security software is enabled, the communication may not be established properly.
PAGE 15
SRC mode The HY144-D-SRC has five SRC modes and they can be changed according to your sound system. Data length and number of inputs/outputs are limited by the selected SRC mode. You can confirm the SRC mode in use from Dante Controller “Device Information” or SLOT settings on the touch screen of the control surface.