User Manual

Effects Parameters
16 RIVAGE PM series Data List
■ Rupert EQ 810
Models a console EQ module that Rupert Neve designed in the 1980s.
■ Portico 5033
This models an analog 5-band EQ made by Rupert Neve Designs.
■ EQ-1A
This processor emulates a vintage EQ that’s considered a classic example of a passive EQ.
Parameter Range Description
LF IN OFF, ON LF band (low shelving) on/off
LF FREQ 33, 56, 95, 160, 270 Hz Cutoff frequency of the LF band (low shelving)
LF GAIN –16.0 to 16.0 dB Gain of the LF band (low shelving)
LMF IN OFF, ON LMF band (peaking) on/off
LMF x3 OFF, ON
Triples the center frequency value of the LMF band
(peaking).
LMF FREQ
40.0 to 400 Hz
*1
*1. When it is On, 120 Hz to 1.20 kHz
Center frequency of the LMF band (peaking)
LMF GAIN –16.0 to 16.0 dB Gain of the LMF band (peaking)
LMF Q 0.90 t0 3.00 Q (steepness) of the LMF band (peaking)
HF IN OFF, ON HF band (high shelving) on/off
HF FREQ 3.3, 4.7, 6.8, 10, 15 kHz Cutoff frequency of the HF band (high shelving)
HF GAIN –16.0 to 16.0 dB Gain of the HF band (high shelving)
HMF IN OFF, ON HMF band (peaking) on/off
HMF x3 OFF, ON
Triples the center frequency value of the HMF band
(peaking).
HMF FREQ
600 Hz to 6.00 kHz
*2
*2. When it is On, 1.80kHz to 18.0 kHz
Center frequency of the HMF band (peaking)
HMF GAIN –16.0 to 16.0 dB Gain of the HMF band (peaking)
HMF Q 0.90 to 3.00 Q (steepness) of the HMF band (peaking)
TRANS. MIC, LINE Type of input transformer that is emulated
DRIVE –20.0 to 20.0
Adjusts the input level to adjust the amount of
overtones.
LPF FREQ OFF, 36, 60, 105, 185, 330 Hz Cutoff frequency of the low pass filter
HPF FREQ OFF, 16, 12, 8.2, 5.6, 3.9 kHz Cutoff frequency of the high pass filter
ALL EQ OFF, ON Turns the LF/LMF/HMF/HF bands on/off together.
Parameter Range Description
ALL BYPASS OFF, ON
Turns bypass on/off for the EQ. Even in the bypassed state, the signal will
pass through the input/output transformers and the amp circuit.
TRIM –12.0 to 12.0 dB Input gain
LF FREQ 30.00 to 300.0 Hz Center frequency of the LF band
LF GAIN –12.0 to 12.0 dB Gain of the LF band
LMF IN OFF, ON Switches the LMF band on/off.
LMF Q 0.70 to 5.00 Q of the LMF band
LMF FREQ 50.00 to 400.0 Hz Center frequency of the LMF band
LMF GAIN –12.0 to 12.0 dB Gain of the LMF band
MF IN OFF, ON Switches the MF band on/off.
MF Q 0.70 to 5.00 Q of the MF band
MF FREQ 330.0 to 2500 Hz Center frequency of the MF band
MF GAIN –12.0 to 12.0 dB Gain of the MF band
HMF IN OFF, ON Switches the HMF band on/off.
HMF Q 0.70 to 5.00 Q of the HMF band
HMF FREQ 1.80k to 16.0k Hz Center frequency of the HMF band
HMF GAIN –12.0 to 12.0 dB Gain of the HMF band
LF/HF IN OFF, ON Switches the LF/HF bands on/off.
HF FREQ 2.50k to 25.0k Hz Center frequency of the HF band
HF GAIN –12.0 to 12.0 dB Gain of the HF band
Parameter Range Description
LOW FREQUENCY
(LO FREQ
*1
)
*1. Actual indication in the screen encoder access field
20, 30, 60, 100 Hz Frequency range of the low range filter
(LOW) BOOST
(LO BOOST
*1
)
0.0 to 10.0 Boost amount of the low range filter
(LOW) ATTEN
(LO ATT
*1
)
0.0 to 10.0 Attenuation amount of the low range filter
HIGH FREQUENCY
(HI FREQ
*1
)
3k, 4k, 5k, 8k, 10k, 12k, 16k Hz Frequency range of the high range filter
(HIGH) BOOST
(HI BOOST
*1
)
0.0 to 10.0 Boost amount of the high range filter
(HIGH) BAND WIDTH
(BAND WID
*1
)
0.0 to 10.0 Band width of the high range filter
(HIGH) ATTEN SEL
(HI ATT F
*1
)
5k, 10k, 20k Hz Frequency range attenuated by the high range filter
(HIGH) ATTEN
(HI ATT
*1
)
0.0 to 10.0 Attenuation amount of the high range filter
IN OFF, ON
Turns the processor on/off. If this is off, the filter section
will be bypassed, but the signal will pass through the
input/output transformers and the amp circuit.
Parameter Range Description