User Manual

Effects Parameters
7 RIVAGE PM series Data List
Effects Parameters
REVERB
■ REV-X
Two input, two output reverb algorithm. Delivers dense and rich reverberation, smooth decay, and
provides a spaciousness and depth that enhances the original sound. Choose from three types
depending on your location and needs; REV-X HALL, REV-X ROOM, and REV-X PLATE.
■ SP2016 Reverb
The SP2016 Reverb is an authentic recreation of the original rack processor from the Eighties. Highly
regarded for its signature reverbs, the SP2016 was used in countless hit records for nearly 40 years. The
SP2016 Reverb plug-in includes vintage and modern versions of Room, Stereo Room and Hi-Density
Plate. The plug-in naturally captures every aspect of the sound of a real physical environment - from
the complex early reflections, to the natural way in which the echo density increases with time, to the
smooth Gaussian decay of the reverb tail. The structure of the reverb can be modified by fine-tuning
the controls - including PreDelay, Decay, Position and Diffusion. The EQ section allows for simple high
and low filtering of the reverb with adjustable filter ranges. The unique Position control takes the
listener from the stage to back of the room increasing the early reflections while retaining all other
settings.
Parameter Range Description
REV TYPE HALL, ROOM, PLATE Reverb type
REV TIME
0.28–27.94 s
*1
*1. These values are for when the effect type is REV-X HALL and the ROOM SIZE=28. The range will differ
depending on the effect type and ROOM SIZE setting.
Reverb time
INI. DLY 1.0–125.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–1.4 Low-frequency reverb time ratio
LO.FREQ 22.0 Hz–18.0 kHz Frequency point for LO.RATIO setting
DIFF. 0–10 Reverb diffusion (left–right reverb spread)
ROOM SIZE 0–28 Size of room
DECAY 0–53 Gate closing speed
HPF THRU, 22.0 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 1.00 kHz–18.0 kHz, THRU Low-pass filter cutoff frequency
Parameter Range Description
PRESET
*1
*1. Refer to the SP2016 Reverb Preset section.
Switches the preset.
PROGRAM
*2
*2. Vintage Stereo Room (STEREO ROOM V) / Vintage Room (ROOM V) / Vintage Plate (HI DENS PLATE V) /
Modern Stereo Room (STEREO ROOM M) / Modern Room (ROOM M) / Modern Plate (HI DENS PLATE M)
Switches between programs (algorithms).
INPUT –inf to +10 dB Adjusts the input level.
OUTPUT –inf to +10 dB Adjusts the output level.
MIX 0 to 100 % Mix balance between dry and wet signals
PREDELAY 1 to 999 ms Pre-delay amount
DECAY 200 ms to 100 s
Reverb time
*3
*3. Use caution when LOW GAIN is set to boost (+), as lengthening the DECAY may cause oscillation.
POSITION 0 to 100 % Front/rear listening position
DIFFUSION 0 to 100 % Diffusion percentage
LOW GAIN –8 to 4 dB
Low-range EQ (shelving) gain
*4
*4. Use caution with long DECAY settings, as boosting (+) the LOW GAIN may cause oscillation.
LOW FREQ 50 to 500 Hz Low-range EQ (shelving) frequency
HIGH GAIN –8 to 0 dB High-range EQ (shelving) gain
HIGH FREQ 1 to 8 kHz High-range EQ (shelving) frequency
KILL ON / OFF Shuts off the input (except when bypass is on).
BYPASS ON / OFF Turning the bypass on or off.
I/O LOCK ON / OFF
If this parameter is set to ON, the input or output level will not
change when the preset is switched.
*5
*5. The input or output level will not be locked during any operation (such as recalling a library), other than when
switching the preset.
MIX LOCK ON / OFF
If this parameter is set to ON, the mix balance will not change
when the preset is switched.
*6
*6. The mix balance will not be locked during any operation (such as recalling a library), other than when switching the
preset.
MONITOR INPUT / OUTPUT Switches the monitoring target of the meter limit indicator.