User Manual

RIVAGE PM7 System Setup Guide
28
9 NETWORK connector
This RJ-45 connector enables you to connect an
external device via an Ethernet cable (CAT5 or
higher).
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard RJ-
45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
) LINK/ACT indicator
This indicator lights up or flashes green, depending
on the connection status.
! OMNI IN jacks
These are balanced XLR-3-31 female input jacks for
inputting analog audio signals from line level devices
or microphones. They feature SILK digital
processing.
@ OMNI OUT jacks
These are balanced XLR-3-32 male output jacks that
transmit analog audio signals.
# AES/EBU jacks
Both input and output jacks feature built-in sampling
rate converters.
IN
These are balanced XLR-3-31 female input jacks that
accept digital audio signals in AES/EBU format.
OUT
These are balanced XLR-3-32 male output jacks for
outputting digital audio signals in the AES/EBU
format.
$ MY card slots
Install optional Mini-YGDAI I/O cards here to
expand I/O ports.
% USB ports
Use these ports to connect a USB storage device such
as a flash drive, USB mouse, or USB keyboard.
^ CONSOLE NETWORK connectors
These RJ-45 connectors allow the unit to be
connected to a console network in a ring topology via
Ethernet cables (CAT5e or higher recommended).
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard
RJ45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
& ERR indicators
This indicator lights up or flashes red if an error
occurs.
In such an event, please contact your Yamaha dealer.
* LINK indicators
This indicator flashes or lights up, depending on the
network status.
( TX/RX indicators
The appropriate indicator flashes green when data is
transmitted from (TX) or received at (RX) the TO
ENGINE OUT/IN connectors.
A NETWORK connector
This RJ-45 connector allows the unit to be connected
to a computer or network device via an Ethernet
cable (CAT5e or higher recommended).
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard
RJ45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
B LINK/ACT indicator
This indicator flashes or lights up green, depending
on the connection status.
Male XLR plug
1 (Ground)
3 (Cold)
2 (Hot)
Female XLR plug
2 (Hot)
3 (Cold)
1 (Ground)
Green
(flashing)
The unit is preparing to connect to the
console network. If it continues flashing,
the system is not functioning properly. If
the problem persists after you take the
following actions, please contact your
Yamaha dealer.
• Turn the power to the RIVAGE PM7
system off and then on.
• Make sure that the cables are
connected properly.
• Make sure that the cables are securely
inserted (locked in).
• Change to a different cable.
Green
(lit steadily)
The unit is connected to the console
network properly.