User Manual

RM Series (RM-CR/RM-CG/RM-TT/RM-WAP) Remote Control Protocol Specifications Version 2.0.0
49
7. Parameter List
Parameter List
Applicable devices RM-CG
Usage example(s)
set
set RM:Mic_Beam/LimitOn 0 0 1
↓
OK set RM:Mic_Beam/LimitOn 0 0 1 “ON”
get
get RM:Mic_Beam/LimitOn 0 0
↓
OK get RM:Mic_Beam/LimitOn 0 0 1
NOTIFY NOTIFY set RM:Mic_Beam/LimitOn 0 0 1 “ON”
No. Case Action Address SubAddress Parameter
x y value min max default
1 Mic input level setting set
setn
sett
setr
get
getn
gett
RM:DSPTOP/MicGaintype 0 0 0 ... 3 0 : 0dB
1 : 15dB
2 : 30dB
3 : 45dB
0 3 3
2 AEC/NR linear processing setting
for Dante output Ch 2
(It enters low-latency mode if there
is no linear processing.
RM:DSPTOP/Output2Mode 0 0 0, 1 0 : LinearProcessing
1 : LowLatency
0 1 0
3 Beam forming tracking speed
setting
RM:
DSPTOP/MaxBeamSpeed
0 0 0 ... 2 0 : Slow
1 : Mid
2 : Fast
0 2 1
4 Beamforming area limit enable RM:Mic_Beam/LimitOn 0 0 1 : Mid 0 : OFF
1 : ON
0 1 0
5 Beamforming area top limit setting RM:Mic_Beam/Top 0 0 -39 ...
40
-39 40 40
6 Beamforming area bottom limit
setting
RM:Mic_Beam/Bottom 0 0 -40 ...
39
-40 39 -40
7 Beamforming area left limit setting RM:Mic_Beam/Left 0 0 -40 ...
39
-40 39 -40
8 Beamforming area right limit setting RM:Mic_Beam/Right 0 0 -39 ...
40
-39 40 40
9 Beamforming area limit floor to
speaker distance setting
RM:
Mic_Beam/Height_FlrToTalk
0 0 0 ... 30 0 30 12
10 Beamforming area limit floor to
RM-CG distance setting
RM:
Mic_Beam/Height_FlrToMic
0 0 20 ...
60
20 60 30
11 Beamforming speed setting
(response speed increases as
the value increases, but accuracy
decreases)
RM:Mic_Beam/Speed 0 0 0, 1 0 : Slow
1 : Fast
0 1 0
12 Echo cancellation level setting
(more echoing is eliminated as the
value increases, but vocal input is
also eliminated)
RM:Mic_Dsp/Aectype 0 0 0 ... 3 0 : Off
1 : Gentle (Low)
2 : Medium
3 : Strong (High)
0 3 2
13 Noise reduction level setting
(more echoing is eliminated as the
value increases, but vocal input is
also eliminated)
RM:Mic_Dsp/Nrtype 0 0 0 ... 3 0 : Off
1 : Gentle (Low)
2 : Medium
3 : Strong (High)
0 3 2
14 Dereverberation level setting
(more echoing is eliminated as the
value increases, but vocal input is
also eliminated)
RM:Mic_Dsp/Derevtype 0 0 0 ... 3 0 : Off
1 : Gentle (Low)
2 : Medium
3 : Strong (High)
0 3 2
15 NearEnd output EQ enable RM:NeOut_EQ/Ch/On/On 0 0 0, 1 0 : OFF
1 : ON
0 1 1
16 NearEnd output EQ band bypass
enable
RM:
NeOut_EQ/Ch/Band/Bypass
0 0 - 5 Band 1 - 6 0, 1 0 : OFF
1 : ON
0 1 0
17 NearEnd output EQ band cutoff
frequency setting
RM:
NeOut_EQ/Ch/Band/
Frequency
0 0 - 5 Band 1 - 6 200 ...
200000
200 : 20[Hz]
...
200000 : 20[kHz]
*See Frequency data
table
200 200000 Band1 :
315
Band2 :
1000
Band3 :
3150
Band4 :
10000
Band5 :
31500
Band6 :
100000
18 NearEnd output EQ band gain
setting
RM:
NeOut_EQ/Ch/Band/Gain
0 0 - 5 Band 1 - 6 -1800
... 1800
-1800 : -18.0[dB]
...
0 : 0.0[dB]
...
1800 : +18.0[dB]
-1800 1800 0