User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Monitor and Cue functions
V5.8 Reference Manual
127
CUE B field
Configures the settings for CUE B.
If the CH/REMOTE switch button (
2) is set to “CH”, switching of the CUE MODE button will
be linked with CUE A/B.
CUE OPERATION MODE field
2
CH/REMOTE switch buttons
This section explains how to use a two-channel CUE.
For example, when a single operator wants to use two separate CUEs, they can be set
separately to an in-ear monitor signal and a floor monitor signal. If a single operator
wants to use a two-channel CUE, select the “CH.” Select the desired CUE SETTINGS for
each channel. You can select from A, B, or A+B. To use one CUE each for the console
and CL Editor/StageMix, select the “REMOTE.” The console is fixed to CUE A, while the
CL Editor/StageMix is fixed to CUE B.
NOTE
When “REMOTE” is selected, the device where CUE is actually turned on and the corresponding
targets are shown in the table below.
3 CUE SETTINGS button
Use this button to open the CUE SETTINGS screen.
1 CUE A ALL button
Press this button to set all channels displayed in the screen to CUE A only. However, if
the selected tab is INPUT, all input channels are set to CUE A only.
2 CUE B ALL button
Press this button to set all channels displayed in the screen to CUE B only. However, if
the selected tab is INPUT, all input channels are set to CUE B only.
3 A/B switch button
Use this button to switch A and B on/off. However, both cannot be turned off at the
same time.
4 Tab
Use these to select the desired edit operation.
NOTE
If the ALTERNATE function is assigned to a USER DEFINED key and the [CUE] key is pressed
while ALTERNATE is on, the channel settings will toggle between A
B A+B each time the
key is pressed.
Device Target
Console CUE A
Cascaded console CUE A
MIDI CUE B
CL Editor CUE B
StageMix CUE B
GPI CUE A
1
4
3
2