User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
Reference Manual
146
About AUTOMIXER
Automixer is included as a standard feature on the CL series. Automixer searches for enabled
mics and automatically optimizes gain distribution, for uses such as speeches without scripts.
This allows uniform system gain to be maintained among multiple mics, freeing the engineer
from making constant fader adjustments.
Automixer operating principle
With the Dugan speech system used in Automixer, you can automatically adjust the automix
gain for up to 16 mics used for speeches.
The Dugan speech system functions differently from a limiter or auto level controller. When
multiple people are speaking, the engineer can adjust the each level using the faders as
normal. Even if nobody is speaking, the system searches for mic audio and automatically
distributes gain. Therefore, faders can be left in their raised positions.
Inserting Automixer in channels post-fader
This section explains how to mount Automixer in a virtual rack, and insert Automixer input and
output into channels (excluding ST IN channels) post-fader (POST ON). For details on
Automixer operations, refer to the following section “Using Automixer.”
Using Automixer
Channel display
The auto mix gain meter for each channel and man (yellow), auto (green), and mute (red)
settings are shown for channels 1-8 and channels 9-16.
If you select the channel 1-8 or 9-16 region, the display channel for the channel control field
will switch to 1-8 or 9-16.
(For 8ch Automixer, only channels 1-8 are shown.)
When 1 person speaks on multiple mics When 2 people speak on multiple mics
When 1 person is speaking, the gain on the mic
being used is immediately increased and the gain
on all other mics is reduced. The same operation
occurs even if another person is speaking.
If 2 people are speaking at the same time, gain is
automatically distributed so that the total gain is
consistent across both mics, and the gain on the
remaining mic is reduced.
Gain (dB) in
Automix
Mic input audio
(dB)
Gain (dB) in
Automix
Mic input audio
(dB)
STEP
1. Refer to steps 1-8 in “Virtual rack operations” (page 136) to mount Automixer in
rack 1 and set its input source and output destination.
2. Refer to “Inserting an external device into a channel” (page 23) to insert Automixer
in post-fader (POST ON field).
Master field
Channel control field